Related Manuals for HP Slate 6 VoiceTab Plus
Summary of Contents for HP Slate 6 VoiceTab Plus
- Page 1 HP Slate 6 VoiceTab Plus Tablet Maintenance and Service Guide IMPORTANT! This document is intended for HP authorized service providers only.
- Page 2 By installing, copying, downloading, or otherwise using any software product preinstalled on this tablet, you agree to be bound by the terms of the HP End User License Agreement (EULA). If you do not accept these license terms, your sole...
- Page 3 Safety warning notice WARNING! To reduce the possibility of heat-related injuries or of overheating the device, do not place the device directly on your lap or obstruct the device air vents. Use the device only on a hard, flat surface. Do not allow another hard surface, such as an adjoining optional printer, or a soft surface, such as pillows or rugs or clothing, to block airflow.
- Page 4 Safety warning notice...
-
Page 5: Table Of Contents
Table of contents 1 Product description ............................1 2 External component identification ........................3 3 Illustrated parts catalog ............................. 5 Locating the product number and the serial number ................5 Tablet major components ........................6 Miscellaneous parts ..........................7 Sequential part number listing ......................8 4 Removal and replacement preliminary requirements .................. - Page 6 7 Power cord set requirements .......................... 28 Requirements for all countries ......................28 Requirements for specific countries and regions ................28 8 Recycling ................................ 30 Index ................................... 31...
-
Page 7: Product Description
Product description Category Description Product Name HP Slate 6 VoiceTab Plus Tablet Processor Qualcomm® MSM8926 1.20-GHz quad core processor, soldered on circuit (SoC) Panel 6.0-in, (1280×720), LCD, 5-point capacitive TouchScreen display panel, bonded, full lamination, OGS; includes display panel cable and TouchScreen cable Memory Supports 1.0-GB LPDDR3 system memory... - Page 8 Category Description Power requirements Supports a 3000-mAh, Li-ion battery (non-removable), USB charging Supports a 5-V, 2-A AC adapter with DC plug and localized cable plug support Operating system Preinstalled: Android 4.4.2 Serviceability End user replaceable part: AC adapter ● Headset ●...
-
Page 9: External Component Identification
External component identification... - Page 10 Item Component Item Component Audio-out (headphone)/Audio-in Front-facing webcam (microphone) jack Rear-facing webcam Volume control buttons (2) Micro USB 2.0 port Power button Battery gauge Microphone Speakers (2) Chapter 2 External component identification...
-
Page 11: Illustrated Parts Catalog
Illustrated parts catalog Locating the product number and the serial number The tablet product number (1) and serial number (2) are located inside the tablet back cover. This information may be needed when travelling internationally or when contacting support. Back cover on page 13 for information on removing the back cover. -
Page 12: Tablet Major Components
Tablet major components Item Component Spare part number Back cover 788634-001 Battery, 3000-mAh (includes cable) 751655-001 Middle frame 788635-001 Button Actuators Kit, includes: 790367-001 (4a) Power button actuator (4b) Volume button actuator Rear-facing webcam (8.0-MP, auto-focus, with flash; includes cable and double- 789611-001 sided adhesive) Ambient light sensor board (includes cable and double-sided adhesive) -
Page 13: Miscellaneous Parts
HP headset 790368-001 HP Slate 6 VoiceTab Plus Tablet equipped with a Qualcomm MSM8926 1.20-GHz quad core processor (SoC), graphics subsystem with UMA memory, 1.0-GB LPDDR3 system memory, and 16-GB eMMC hard drive, and a 6.0-in, (1280×720), LCD, 5-point capacitive TouchScreen, bonded, full lamination, OGS, display panel assembly... -
Page 14: Sequential Part Number Listing
Middle frame 788636-001 HP Slate 6 VoiceTab Plus Tablet equipped with a Qualcomm MSM8926 1.20-GHz quad core processor (SoC), graphics subsystem with UMA memory, 1.0-GB LPDDR3 system memory, and 16-GB eMMC hard drive, and a 6.0-in, (1280×720), LCD, 5-point capacitive TouchScreen,... -
Page 15: Removal And Replacement Preliminary Requirements
Removal and replacement preliminary requirements Tools required You will need the following tools to complete the removal and replacement procedures: Magnetic screw driver ● Phillips P0 screw driver ● Plastic case utility tool ● Service considerations The following sections include some of the considerations that you must keep in mind during disassembly and assembly procedures. -
Page 16: Grounding Guidelines
Grounding guidelines Electrostatic discharge damage Electronic components are sensitive to electrostatic discharge (ESD). Circuitry design and structure determine the degree of sensitivity. Networks built into many integrated circuits provide some protection, but in many cases, ESD contains enough power to alter device parameters or melt silicon junctions. -
Page 17: Packaging And Transporting Guidelines
Packaging and transporting guidelines Follow these grounding guidelines when packaging and transporting equipment: To avoid hand contact, transport products in static-safe tubes, bags, or boxes. ● Protect ESD-sensitive parts and assemblies with conductive or approved containers or ● packaging. Keep ESD-sensitive parts in their containers until the parts arrive at static-free workstations. ●... - Page 18 Equipment guidelines Grounding equipment must include either a wrist strap or a foot strap at a grounded workstation. When seated, wear a wrist strap connected to a grounded system. Wrist straps are flexible ● straps with a minimum of one megohm ±10% resistance in the ground cords. To provide proper ground, wear a strap snugly against the skin at all times.
-
Page 19: Removal And Replacement Procedures
Removal and replacement procedures Tablet component replacement procedures CAUTION: Tablet components described in this chapter should only be accessed by an authorized service provider. Accessing these parts can damage the tablet and void the warranty. This chapter provides removal and replacement procedures for authorized service provider only parts. -
Page 20: Battery
WARNING! To reduce potential safety issues, use only the battery provided with the tablet, a replacement battery provided by HP, or a compatible battery purchased from HP. CAUTION: Removing a battery that is the sole power source for the tablet can cause loss of information. - Page 21 Use the finger notch (1) to release the bottom edge of the battery (2) from the middle frame. Remove the battery (3). Reverse this procedure to install the battery. Battery...
-
Page 22: Middle Frame
Middle frame Description Spare part number Middle frame 788635-001 Before removing the middle frame, follow these steps: Turn off the tablet. If you are unsure whether the tablet is off or in Hibernation, turn the tablet on, and then shut it down through the operating system. Disconnect the power from the tablet by unplugging the power cord from the tablet. - Page 23 NOTE: If the power button actuator or the volume button actuator should become displaced during the removal of the middle frame, install the actuators into the openings in the middle frame as indicated in the following illustration. The fingers (1) on the ends of the actuators should be installed on the slots (2) and (3) on the middle frame.
-
Page 24: Rear-Facing Webcam
Rear-facing webcam Description Spare part number Rear-facing webcam (8.0-MP, auto-focus, with flash; includes cable and double-sided adhesive) 789611-001 Before removing the rear-facing webcam, follow these steps: Turn off the tablet. If you are unsure whether the tablet is off or in Hibernation, turn the tablet on, and then shut it down through the operating system. -
Page 25: Antenna Board
Antenna board Description Spare part number Antenna board (includes RF cable and double-sided adhesive) 773133-001 Before removing the antenna board, follow these steps: Turn off the tablet. If you are unsure whether the tablet is off or in Hibernation, turn the tablet on, and then shut it down through the operating system. -
Page 26: Speaker And Vibrator Module
Reverse this procedure to install the antenna board. Speaker and vibrator module Description Spare part number Speaker (bottom, includes vibrator module, double-sided adhesive, and cables) 790370-001 Before removing the bottom speaker and vibrator module, follow these steps: Turn off the tablet. If you are unsure whether the tablet is off or in Hibernation, turn the tablet on, and then shut it down through the operating system. -
Page 27: System Board
Release the bottom speaker (3) from the molding built into the display panel assembly. Remove the bottom speaker and vibrator module. Reverse this procedure to install the bottom speaker and vibrator module. System board Description Spare part number System board equipped with a Qualcomm MSM8926 1.20-GHz quad core processor (SoC), 788638-001 graphics subsystem with UMA memory, 1.0-GB LPDDR3 system memory, and 16-GB eMMC hard drive (includes top speaker) - Page 28 Disconnect the following cables from the system board: (1) RF antenna cable (2) Ambient light sensor board cable (3) TouchScreen cable Release the top speaker cable (4) from the clip built into the display panel assembly.xxx Detach the top speaker (5) from the display panel assembly. (The top speaker is attached to the display panel assembly with double-sided adhesive.) Chapter 5 Removal and replacement procedures...
- Page 29 Disconnect the following cables from the system board: (1) Rear-facing webcam cable (2) Front-facing webcam cable (3) Display panel cable (4) Vibrator module cable Remove the Phillips PM1.3×3.3 screw (1) that secures the system board to the display panel assembly. System board...
-
Page 30: Front-Facing Webcam
Remove the system board (2). Reverse this procedure to install the system board. Front-facing webcam Description Spare part number Front-facing webcam (2.0-MP, fixed-focus; includes cable) 789610-001 Before removing the front-facing webcam, follow these steps: Turn off the tablet. If you are unsure whether the tablet is off or in Hibernation, turn the tablet on, and then shut it down through the operating system. -
Page 31: Ambient Light Sensor Board
Turn the system board upside down. Disconnect the front-facing webcam cable (1) from the system board. Remove the front-facing webcam (2). Reverse this procedure to install the front-facing webcam. Ambient light sensor board Description Spare part number Ambient light sensor board (includes cable and double-sided adhesive) 790369-001 Before removing the ambient light sensor board, follow these steps: Turn off the tablet. - Page 32 Remove the ambient light sensor board: Detach the ambient light sensor board from the display panel assembly. (The ambient light sensor board is attached to the display panel assembly with double-sided adhesive.) Remove the ambient light sensor board and cable. Reverse this procedure to install the ambient light sensor board.
-
Page 33: Specifications
The tablet operates on DC power, which can be supplied by an AC or a DC power source. The AC power source must be rated 100—240 V, 50/60 Hz. NOTE: The tablet can operate on DC power using an industry-standard micro-B USB cable. The HP adapter included with the tablet is recommended for charging the tablet. Temperature Operating 5°C to 35°C... -
Page 34: Power Cord Set Requirements
Power cord set requirements The wide-range input feature of the tablet permits it to operate from any line voltage from 100 to 120 volts AC, or from 220 to 240 volts AC. The 3-conductor power cord set included with the tablet meets the requirements for use in the country or region where the equipment is purchased. - Page 35 Country/region Accredited agency Applicable note number Sweden CEMKO Switzerland Taiwan BSMI The United Kingdom The United States The flexible cord must be Type HO5VV-F, 3-conductor, 1.0-mm² conductor size. Power cord set fittings (appliance coupler and wall plug) must bear the certification mark of the agency responsible for evaluation in the country or region where it will be used.
-
Page 36: Recycling
Follow the local laws and regulations in your area for battery disposal. HP encourages customers to recycle used electronic hardware, HP original print cartridges, and rechargeable batteries. For more information about recycling programs, see the HP Web site at http://www.hp.com/recycle. Chapter 8 Recycling... -
Page 37: Index
Index AC adapter, spare part numbers front-facing webcam packaging guidelines 11 7, 8 location 4 plastic parts, service ambient light sensor board removal 24 considerations 9 removal 25 spare part number 6, 8, 24 ports spare part number 6, 8, 25 product description 1 antenna board USB 2.0 4... - Page 38 connectors 9 plastic parts 9 serviceability, product description 2 SIM, spare part number 7, 8 speaker location 4 removal 20 spare part number 6, 8, 20 system board removal 21 spare part number 6, 8, 21 tablet major components 6 spare part numbers 7, 8 specifications 27 tools required 9...