Table of Contents
Advertisement
FUNCTION
■ CLEANING
COPIER> FUNCTION> CLEANING
TBLT-CLN
Toner ejection and ITB cleaning
Details
To form a halftone band on the ITB and execute ITB cleaning.
Deteriorated toner can be ejected, and soiling on the ITB can be
removed.
The same processing is performed by selecting the following: Settings/
Registration> Adjustment/Maintenance> Maintenance> Clean Inside
Main Unit.
Use case
• When removing the soiling on the ITB
• When ejecting the deteriorated toner
Adj/set/operate method Select the item, and then press Start key.
Display/adj/set range
During operation: ACTIVE, When the operation finished normally: OK!
Related UI menu
Adjustment/Maintenance> Maintenance> Clean Inside Main Unit
2TR-CLN
Clean of Secondary Transfer Outer Roller
Details
To clean soiling adhered on the Secondary Transfer Outer Roller.
Transfer toner to the Secondary Transfer Outer Roller once and then
execute bias cleaning to remove soiling.
Use case
• When the backside of the paper is soiled by the Secondary Transfer
Outer Roller
• When contacting with the Secondary Transfer Outer Roller at the
time of jam processing, etc.
Adj/set/operate method Select the item, and then press Start key.
Display/adj/set range
During operation: ACTIVE, When operation finished normally: OK!
TNR-COAT
Exe toner application to Sec Trns Roller
Details
When the Secondary Transfer Outer Roller is replaced with a new one,
substances leaking from the new roller may adhere to the ITB.
By executing this item after replacement, Y-color toner is applied onto
the surface of the roller, so adhesion of substances leaking from the
roller can be prevented.
Use case
When replacing the Secondary Transfer Outer Roller
Adj/set/operate method Select the item, and then press Start key.
Caution
Be sure to execute this item to the roller which surface is not soiled.
Display/adj/set range
During operation: ACTIVE, When operation finished normally: OK!
8
Service Mode > COPIER > FUNCTION > PART-CHK
T-8-26
8
Service Mode > COPIER > FUNCTION > PART-CHK
■ PART-CHK
COPIER> FUNCTION> PART-CHK
CL
Specification of operation Clutch
Details
To specify the Clutch to operate.
Use case
When replacing the Clutch/checking the operation
Adj/set/operate method Enter the value, and then press Start key.
Display/adj/set range
0 to 1
1: Developing Cylinder Clutch (Y) (CL01)
2: Developing Cylinder Clutch (M) (CL02)
3: Developing Cylinder Clutch (C) (CL03)
4: Developing Cylinder Clutch (Bk) (CL04)
Related service mode
COPIER> FUNCTION> PART-CHK> CL-ON
CL-ON
Operation check of Clutch
Details
To start operation check of the clutch specified by CL.
The specified clutch is turned ON 1 second from the Developing Motor
(M03) is turned ON, and then both the motor and the clutch are
turned OFF 5 seconds later.
Use case
When replacing the Clutch/checking the operation
Adj/set/operate method Select the item, and then press Start key.
Display/adj/set range
During operation: ACTIVE, When operation finished normally: OK!
Related service mode
COPIER> FUNCTION> PART-CHK> CL
FAN
Specification of operation Fan
Details
To specify the Fan to operate.
Use case
When replacing the Fan/checking the operation
Adj/set/operate method Enter the value, and then press Start key.
Display/adj/set range
1 to 10
1: Drum Unit Suction Cooling Fan (FM01)
2: Duplex Cooling Fan (FM04)
3: Delivery Cooling Fan (FM03)
4 to 10: Not used
Default value
1
Related service mode
COPIER> FUNCTION> PART-CHK> FAN-ON
FAN-ON
Operation check of Fan
Details
To start operation check of the Fan specified by FAN.
Use case
When replacing the Fan/checking the operation
Adj/set/operate method Select the item, and then press Start key.
Display/adj/set range
During operation: ACTIVE, When operation finished normally: OK!
Related service mode
COPIER> FUNCTION> PART-CHK> FAN
8-72
8-72
Advertisement
Table of Contents
Troubleshooting
