Page 3
Thank you for choosing a first class product from Electrolux, which hopefully will provide you with lots of pleasure in the future. The Electrolux ambition is to offer a wide variety of quality products that make your life more comfortable.
This appliance is manufactured according to the following EEC directives: 2006/95 EEC - 2004/108 EEC - 90/396 EEC, current edition. MANUFACTURER: ELECTROLUX ITALIA S.p.a. C.so Lino Zanussi, 30 33080 PORCIA (PN) - Italy These instructions are only valid for countries whose identification symbols are shown...
5 Important safety information You MUST read these warnings carefully before installing or using the hob. If you need assistance, contact our Customer Care Department on 08705 950950. Installation This appliance must be installed and serviced by a competent person as stated in the Gas Safety (Installation and Use) Regulations Current Editions and the IEE Wiring Regulations.
Page 6
6 electrolux When using the hob for a long period time, the ventilation should be improved, by opening a window or increasing the extractor speed. Do not use this hob if it is in contact with water. Do not operate the hob with wet hands.
7 Description of the hob Rapid Burner Semi-rapid Burner Auxiliary Burner Dual Burner Control knobs INSTALLATION Any gas installation must be carried out by a registered competent person, and in accordance with existing rules and regulations. The relevant instructions are to be found in the second section of this manual.
8 electrolux Operation Hob burners control knobs The symbols on the knobs mean that : there is no gas supply there is maximum gas supply there is minimum gas supply Lighting the burners For easier lighting, proceed before putting a pan on the pan support.
Page 9
9 After lighting the flame, keep the knob pushed down for about 5 seconds. This will allow the "thermocouple" (Fig. 2 - lett. D) to be heated and the safety device to be switched off, otherwise the gas supply would be interrupted.
10 electrolux Using the hob correctly To ensure maximum burner efficiency, it is strongly recommended that you use only pots and pans with a flat bottom fitting the size of the burner used, so that flame will not spread beyond the bottom of the vessel (see the table below).
11 Maintenance and Cleaning Before any maintenance or cleaning can be carried out, you must DISCONNECT the hob from the electricity supply. The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool.
12 electrolux The Burners The burner caps and crowns can be removed for cleaning. Wash the burners caps and crowns using hot soapy water, and remove marks with a mild paste cleaner. A well moistened soap impregnated steel wool pad can be used with caution, if the marks are particularly difficult to remove.
13 Something not working? If the hob is not working correctly, please carry out the following checks before contacting your local Service Force Centre. symptom solution There is no spark when Check that the unit is plugged lighting the gas.
14 electrolux Instructions for the Installer Engineer technical data OVERALL dimensions Width: 744 mm Depth: 510 mm CUT OUT dimensions Width: 560 mm Depth: 480 mm SUPPLY CONNECTIONS Gas: R 1/2 inch (1/2 inch male) Rear right hand corner Electric:...
16 electrolux Important safety requirements This hob must be installed in accordance with the Gas Safety (Installation and Use) Regulations (Current Edition) and the IEE Wiring Regulations (Current Edition). For appliances installed in the Republic of Ireland please refer to NSAI- Domestic Gas Installation I.S.
17 For appliances installed in the Republic of Ireland please refer to NSAI- Domestic Gas Installation I.S 813 Current Edition Section 7- Permitted Locations of Appliance. Installation IMPORTANT Any gas installation must be carried out by a GAS SAFE REGISTER installer.
18 electrolux Building In Building over a cupboard or drawer If the hob is to be installed above a cupboard or drawer it will be necessary to fit a heat resistant board below the base of the hob on the underside of the work surface.
19 Fitting the hob into the worktop Carry out the building in of the hob as follows: 1. place the seals supplied with the hob on the front edge of the cut out. Then, place them at 86 mm from the side edges and at 10 mm from the rear edge, as shown in Fig.3,...
20 electrolux Electrical connections Any electrical work required to install this hob should be carried out by a qualified electrician or competent person, in accordance with the current regulations. THIS HOB MUST BE EARTHED. The manufacturer declines any liability should these safety measures not be observed.
21 The replacement of electric cable must be carried out ex- clusively by the service force centre or by personnel with similar competencies, in accordance with the current regu- lations. Permanent Connection In the case of a permanent connection, it is necessary that you install a...
23 Fault finding Preliminary Electrical Systems Check Blue Brown Green Yellow START Isolate appliance and carry out: A: Earth Continuity Blue check. Green Brown Yellow Carry out: C: Polarity check. Carry out: D: Resistance to Earth check. Has inlet fuse blown?
Page 24
24 electrolux A. EARTH CONTINUITY CHECK Appliance must be electrically disconnected - meter set on W (Ohms) x 1 scale and adjust zero if necessary. — Test leads from any appliance earth point to earth pin on plug. Resistance should be less than 0.1 W (Ohm), check all earth wires for continuity and all contacts clean and tight.
Page 25
25 Ignition System / Gas Ignition Check gas supply at Ignitor does not spark burner Check plug top fuse and Light burner manually replace if necessary Check polarity and Check by pass simmer earth continuity of adjusted supply point...
26 electrolux Commissioning When the hob has been fully installed it will be necessary to check the minimum flame setting. To do this, follow the procedure below. Turn the gas tap to the MAX position and ignite. 2. Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several times.
27 Conversion from natural gas to LPG IMPORTANT The replacement/conversion from natural gas to LPG should only be undertaken by a competent person. It is important to note that this model is designed for use with natural gas but can be converted for use with butane or propane gas providing the correct injectors are fitted.