HP Z800 - Workstation - 6 GB RAM Installation Manual
Hp z800 workstation - hp 2.5-inch hard drive 2:1 optical bay bracket installation
Hide thumbs
Also See for Z800 - Workstation - 6 GB RAM:
- Maintenance and service manual (266 pages) ,
- Installation manual (7 pages) ,
- Installation (2 pages)
Table of Contents
Advertisement
Quick Links
HP 2.5-inch Hard Drive 2:1 Optical Bay
Bracket
Introduction
This document describes how to install Small Form Factor (SFF) SATA hard drives in the HP 2.5-inch
hard drive 2:1 optical bay bracket and install the bracket in the optical drive bay of an HP
Kit contents
Choose the applicable kit from the table.
HP 2.5-inch Hard Drive 2:1 Optical Bay Bracket kit
●
HP 2.5-inch hard drive 2:1 optical bay bracket
●
Y-adapter power cable
●
Warranty information
●
Installation instructions (this document)
System requirements
●
Available optical bay position
●
One unused port connector for each hard drive being installed
Before you begin
To view QuickSpecs and determine the compatibility of this product with your HP workstation, see
http://www.hp.com/go/productbulletin.
ENWW
HP 2.5-inch SATA Hard Drive kit
●
SFF SATA hard drive
●
Data cables
●
Warranty information
●
Installation instructions (this document)
© 2009 Hewlett-Packard Development Company, L.P. Printed in the U.S.
Workstation.
Introduction
1
Advertisement
Table of Contents
Related Manuals for HP Z800 - Workstation - 6 GB RAM
Summary of Contents for HP Z800 - Workstation - 6 GB RAM
-
Page 1: Kit Contents
One unused port connector for each hard drive being installed Before you begin To view QuickSpecs and determine the compatibility of this product with your HP workstation, see http://www.hp.com/go/productbulletin. © 2009 Hewlett-Packard Development Company, L.P. Printed in the U.S. ENWW Introduction... -
Page 2: Warnings And Cautions
Warnings and cautions WARNING! Any surface or area of the equipment marked with this symbol indicates the presence of an electrical shock hazard. To reduce the risk of injury from electrical shock, do not open any enclosed area marked with this symbol. WARNING! To reduce the risk of electric shock or damage to your equipment: —... -
Page 3: Step 1-Preparing For Component Installation
Step 1—Preparing for component installation NOTE: Workstation models vary. All illustrations are examples only. Accessing the internal components of the workstation If you need help preparing the workstation for this installation, consult the removal and replacement procedures in the service guide for your workstation at http://www.hp.com/support/ workstation_manuals. -
Page 4: Step 2-Installing The Hard Drive
Step 2—Installing the hard drive The hard drive bracket accommodates two SFF hard drives. To prepare the hard drives to be inserted in the drive bracket: Remove the green rails from the bracket by squeezing the tabs and sliding the rails out of the bracket. -
Page 5: Step 3-Configuring The Cabling
Slide the drive into the bay, releasing the latch just before the drive is fully-seated, allowing the latch pins to engage. Figure 3 Installing the bracket in the optical bay Step 3—Configuring the cabling In HP 600 and HP 800 Workstations, if the internal bays are not filled to capacity, the pre-installed blind-mate data cables for the unused internal hard drive bays might have to be unplugged from the system board, to enable the proper connection of the hard drives installed in this bracket. -
Page 6: Step 4-Reassembling The Workstation
Repeat the data cable connection for the second hard drive. Figure 4 Connecting the power and data cables to the hard drives Step 4—Reassembling the workstation Reinstall the front bezel, if applicable. Reinstall the card support, if applicable. Reinstall the airflow guide, if applicable. Reinstall the side access panel.