Paradox PCS265 LTE Installation And Programming Manual
Lte / 4g / 3g / 2g / gsm communicator module
Hide thumbs
Also See for PCS265 LTE:
Advertisement
Quick Links
PCS265 LTE
LTE / 4G / 3G / 2G / GSM
Communicator Module
Installation and Programming Guide
**Compatible with Insite GOLD
and SWAN Server**
Installation
1
1 Mounting hole
2
2 Antenna connector
3
3 Wall tamper hole
4 Serial connector
5 RS485 / power terminal
8
6 Upgrade connector
7
7 Battery terminal
8 Cover tamper switch
4
6
1
5
SIM Card Connection
The PCS265 LTE supports two standard LTE/4G/3G/2G or GSM
provider SIM cards. To install the SIM cards, open the SIM Card tray
and insert card into slot, as shown. SIM Card 1 is used as "Primary"
and SIM Card 2 for "Backup".
Panel Connections
Connect the PCS265 LTE's serial out to the serial connector on the
panel.
• For LTE/4G/3G/2G reporting, connect to the Serial port of
the panel.
• For GSM reporting, connect to the EBUS port of the panel.
LTE/4G/3G/2G (Serial Connector)
GSM (EBUS Connector)
PCS265L-EI03 07/2019
RS485 Connection
A CVT485 module can be connected onto the control panel's EBUS in
order to lengthen the distance (up to 300 m. / 1000 ft.) between the
panel and the PCS265 LTE. Refer to the drawing for connections.
Up to 300m (1000 ft.)*
Up to 50m (160 ft.) AWG18
External Antenna Connection
Use the ANTK4G LTE external antenna kit for PTCRB installations or
to improve RF reception if your module's signal strength is weak.
External antenna kits and extension kits are purchased separately.
IP Module Connection
The PCS265 LTE can be connected to an IP Internet Module's PCS
port. For more information on how to configure this option, please
refer to the IP module's Installation manual.
Powering-up the PCS265 LTE
Once your hardware connections are completed, the PCS265 LTE
module will begin its power up sequence.
• Power LED will turn solid green
• Status LED will be red and switch to green after approximately 10
seconds
• SIM card 1 LED will slowly flash orange while searching for the
GSM network; once found the LED will be solid orange
If configured for LTE/4G/3G/2G reporting, you will need to configure
network provider information. Refer to the Programming section.
Note: Ensure that the PCS265 LTE's battery is always present and
that the battery is replaced when low; do not allow the battery to
deplete.
The battery function is to support power shut down and not to be used
as backup as defined in EN50131-6.
LED Functionality
LED
Functionality
SIM1 and SIM2 Slow orange flashing - Searching the network
Solid blue - LTE/4G/3G
Solid orange - GSM
Solid green - 2G (n/a for North and South America)
Quick flashing - Exchanging data (the color of the
flashing LED corresponds to the color of LTE/4G/3G/
2G or GSM depending on which is being used)
Off - SIM card 1 or 2 is not installed, not active, or
currently not in use
Power
Solid green
Off - No power
Status
Red - Error condition, no firmware
Red/Green alternating - updating firmware
Green - No error and/or battery fully charged
Amber - Battery charging
Signal Strength Three LEDs indicate network strength
All LEDs
Flashing - No data communication
(except power)
Programming
In order to configure the PCS265 LTE for reporting, you will need to
first configure your SIM cards. Please note that SIM Card 1 can be
configured via panel programming and SIM Card 2 via SMS.
CVT485
LTE/4G/3G/2G Reporting (Serial Port Connection)
Network Provider Information
MG/SP
EVO
[921]
[2960]
[922]
[2961]
[923]
[2962]
[924]
[2963]
[925]
[2964]
[926]
[2965]
Important: This information can be obtained from your mobile net-
work provider.
Network Provider Information via SMS
Command
P[password].
APN2.NAME. [Access
Point Name]
P[password].
APN2.USER.[Access
Point Name]
P[password].
APN2.PSW.[Access Point
Name]
P[password].
APN2.CLEAR
P[password].
VAPN2.[CALL BACK
PHONE NUMBER]
LTE/4G/3G/2G Reporting Options
MG/SP
EVO
[918]
[2976] to
[919]
[2983]
[806]
[2975]
Feature
APN part 1 (characters 1-16)
APN part 2 (characters 17-32)
APN user name part 1 (1-16)
APN user name part 2 (17-32)
APN password part 1 (1-16)
APN password part 2 (17-32)
Description
Used to program the SIM Card 2 Access
Point Name
Used to program the SIM Card 2 Access
Point User
Used to program the SIM Card 2 Access
Point Password
Used to clear the SIM Card 2 Access
Point Name
Used to view the SIM Card 2 Access
Point Name information
Feature
Details
Account / Partition
MG/SP: Sections
Registration
represent account/
partition 1 and 2
EVO: Sections
represent account /
partition 1 to 8
[7] Off + [8] Off = landline only
[7] Off + [8] On = LTE/4G/3G/2G primary /
landline backup (default)
[7] On + [8] Off = landline only
[7] On + [8] On = landline and LTE/4G/3G/2G
in parallel
PARADOX.COM
Advertisement
Related Manuals for Paradox PCS265 LTE
Summary of Contents for Paradox PCS265 LTE
- Page 1 Programming A CVT485 module can be connected onto the control panel’s EBUS in In order to configure the PCS265 LTE for reporting, you will need to order to lengthen the distance (up to 300 m. / 1000 ft.) between the first configure your SIM cards.
-
Page 2: Technical Specifications
Finnish Patents P[password].DNS.CLEAR Clear domain name server (DNS) IP Hungarian Estonian Your use of the Paradox product signifies your acceptance of these terms and address conditions. The following US patents may apply 5,886,632 and 6,215,399. Other Czech French Canadian P[password].VIP.[phone Get domain name server (DNS) info Canadian and international patents may apply.