Table of Contents SAFE SERVICING PRACTICES .......... 1 WIRING DIAGRAM............... 2 SECTION A - INSTALLATION INSTRUCTIONS ....3 FOR YOUR SAFETY ......................3 WARM & SERVE DRAWER DIMENSIONS ................ 3 IMPORTANT NOTES TO THE INSTALLER ................ 4 IMPORTANT NOTE TO THE CONSUMER................. 4 IMPORTANT SAFETY INSTRUCTIONS ................
Section A - Installation Instructions INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER. IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE. READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. FOR YOUR SAFETY: Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
Section A - Installation Instructions Important Notes to the Installer 1. Read all instructions contained in these installation instructions before installing appliance. 2. Remove all packing material from appliance before connecting the electrical supply. 3. Observe all governing codes and ordinances. 4.
Section A - Installation Instructions Warm & Serve Drawer Installation 1. Locate the 2 anti-tip brackets supplied as shown on figure 1. 2. Slide drawer into cutout opening until front frame of drawer is flush against cabinet. Be careful not to pinch electrical cord.
Section B - Replacement of parts 1.0 HOW TO REMOVE THE DRAWER FROM THE DRAWER CAVITY 1. Disconnect Warmer Drawer from electrical supply. 2. Make sure the drawer is COOL. Open the drawer to the fully opened position 3. Locate the latches on both sides of the warmer drawer. Push at the same time on both latches while pulling the drawer out.
Section B - Replacement of parts 4.0 HOW TO REMOVE PANELS TO HAVE ACCESS TO THE PARTS 1. Disconnect Warmer Drawer from electrical supply. 2. Remove the drawer from the drawer cavity. (Section 1.0) 3. Remove the appliance from the cabinet. (Section 3.0) 4.
Section B - Replacement of parts 5.0 HOW TO REPLACE THE ELECTRICAL CORD 1. Disconnect Warmer Drawer from electrical supply. 2. Remove the drawer from the drawer cavity. (Section 1.0) 3. Remove the appliance from the cabinet. (Section 3.0) 4. The electrical cord is located at rear of the appliance proceed from steps 4 to 6 under section 3.0 to have access to the electrical cord.
Section B - Replacement of parts 7.0 HOW TO REPLACE THE THERMOSTAT 1. Disconnect Warmer Drawer from electrical supply. 2. Remove the drawer from the drawer cavity. (Section 1.0) 3. Remove the appliance from the cabinet. (Section 3.0) 4. Proceed from steps 4 to 6 under section 3.0 to have access to the thermostat.
Section B - Replacement of parts 8.0 HOW TO REPLACE THE WARMER DRAWER CONTROL (CONTINUED) 5. Remove the 2 screws. (Figure 11) 6. Replace the drawer control by the side access and reassemble in reverse order. Figure 11 9.0 HOW TO REPLACE THE SLIDING CHANNELS 1.
Page 15
Section B - Replacement of parts THIS IS A BLANK PAGE...
Section C - Exploded view drawings BODY PARTS DESCRIPTION Position No Part No Description 13A# 316095500 Switch, Infinite, Warmer 318250400 Light, Indicator, Blue 318246900 Panel, Control, Stainless 318228100 Strain Relief 318017600 Knob, Warmer 318144001 Cord, Service 318250500 Lens, Indicator Light 5303323134 Screw, Switch Mtg., 8-32 X 0.188 318141920...
Section C - Exploded view drawings DRAWER PARTS DESCRIPTION Position No Part No Description 318246400 Drawer, Warmer w/Track 318247000 Glass, Drawer Panel, Black 5303325168 Screw, 10-32 X 5/8, Handle Mtg 318248400 Channel, Drawer Slide, Outer 318238900 Handle, Oven Door, Stainless 318141920 Bumper, Base 318247300...