Page 1
DSR-PD150/PD150P RMT-811 SERVICE MANUAL SERVICE MANUAL US Model Canadian Model Ver 1.0 2000. 05 DSR-PD150 AEP Model DSR-PD150P C MECHANISM Photo : DSR-PD150 NTSC model : DSR-PD150 PAL model : DSR-PD150P SPECIFICATIONS — Continued on next page — DIGITAL CAMCORDER...
Page 2
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU PUBLISHED BY SONY.
REPAIR PARTS LIST 3-1-2. Precautions on Adjusting ··············································· 5-58 3-1-3. HOW TO ENTER RECORD MODE WITHOUT 6-1. EXPLODED VIEWS ······················································ 6-1 CASSETTE ··································································· 5-58 6-1-1. OVERALL SECTION-1 ················································· 6-1 3-1-4. HOW TO ENTER PLAYBACK MODE WITHOUT 6-1-2. OVERALL SECTION-2 ················································· 6-2 CASSETTE ···································································...
SERVICE NOTE POWER SUPPLY DURING REPAIRS In this unit, about 10 seconds after power is supplied to the battery terminal using the regulated power supply (8.4V), the power is shut off so that the unit cannot operate. These following two methods are available to prevent this. Take note of which to use during repairs. Method 1.
SELF-DIAGNOSIS FUNCTION SELF-DIAGNOSIS FUNCTION SELF-DIAGNOSIS DISPLAY When problems occur while the unit is operating, the counter of the When problems occur while the unit is operating, the self-diagnosis function starts working, and displays on the viewfinder, LCD screen viewfinder, LCD screen or LCD window consists of an alphabet or LCD window what to do.
Page 6
SELF-DIAGNOSIS CODE TABLE Self-diagnosis Code Block Detailed Symptom/State Correction Function Code Non-standard battery is used. Use the info LITHIUM battery. Condensation. Remove the cassette, and insert it again after one hour. Video head is dirty. Clean with the optional cleaning cassette. LOAD direction.
Page 7
DSR-PD150/PD150P SECTION 1 This section is extracted from instruction GENERAL manual. (DSR-PD150P)
2-2. EVF SECTION (LB-065D BOARD) 4 EVF front cabinet (upper) 2 EVF rear cabinet assembly 1 Push the lock knob in the direction of the arrow A and remove the EVF rear cabinet assembly in the direction of the arrow B . 3 Two tapping 5 EVF front cabinet screws (M1.7 ×...
2-3. UPPER HANDLE BLOCK ASSEMBLY 9 Upper handle block assembly 4 Tilt up the finder. 2 Two screws (M2 × 5), spring bolt 3 Screw (M2 × 5), spring bolt 1 Two screws (M2 × 5), spring bolt 6 Tilt down the finder.
Page 51
2-5. XD-001, XS-001, XM-001 BOARDS 7 Screw (M2.6) Remove the XM-001 board 8 Cable holder and XLR sheet metal in the direction of the arrow. 6 Four screws (M2.6) 5 Two FP-217 flexible boards (16P) 0 XM-001 board, XLR sheet metal 3 Two screws (M2 ×...
[MECHANISM DECK SERVICE POSITION-1] Note: Use the parts only which can be removed easily from outside of the mechanism deck. Adjustment remote commander (RM-95) LANC jack CPC-13 jig Mechanism deck (J-6082-443-A) AC POWER AC IN ADAPTOR Cabinet (L) block assembly [SERVICE POSITION TO CHECK THE VTR SECTION] Connection to Check the VTR Section To check the VTR Section, set the VTR to the "forced VTR power ON"...
[CONNECTION DIAGRAM FOR SERVICE POSITION (Mainly for voltage measurement and check)] CK-093, VC-242D, JK-190, CD-254, DD-138D, LA-026, KP-010, MK-014, MS-049 BOARDS, MECHANISM DECK-2 Battery panel assembly AC POWER AC IN ADAPTOR CPC-13 jig DC-IN (J-6082-443-A) connector (3P) (1-794-637-11) Battery terminal board (4P) KP-010 board MK-014 board DD-138D board...
Page 60
2-16.CONTROL SWITCH BLOCK (ED-4980), HINGE ASSEMBLY Start the removal work after the LCD section has been removed referring section 2-1. 2 Control switch block (ED-4980) 1 Bright button 3 Blind door (D) assembly 2 Screw (M1.7 × 2.5), 2 Hinge lid 3 Three claws lock ace q;...
Page 61
2-17.CIRCUIT BOARDS LOCATION The circuit boards contained in the zoom lens are not shown. LB-065D MA-386D (BACK LIGHT) CK-093 XM-001 (AUDIO AMP) (MIC AMP) (KEY IN) XD-001 (DC/DC CONVERTER SIRCS) PD-126 (RGB DRIVE/TG) INVERTER TRANSFORMER UNIT XS-001 HL-011 (MIC SELECT) (LCD DRIVE) SE-108 CD-254...
Page 62
2-18.FLEXIBLE BOARDS LOCATION The flexible boards contained in the mechanism deck and that in the zoom lens are not shown. FP-193 FP-202 FP-200 FP-216 FP-217 FP-218 FP-194 FP-190 FP-196 FP-189 FP-195 FP-188 FP-191 CONTROL SWITCH BLOCK (ED-4980) CONTROL SWITCH BLOCK FP-186 (PS-4980) FP-197...
Page 63
DSR-PD150/PD150P SECTION 3 BLOCK DIAGRAMS 3-1. OVERALL BLOCK DIAGRAM (1/4) ( ) : Page No. shown in ( ) indicates the page to refer on the schematic diagram. CD-254 BOARD VC-242D BOARD(1/4) (4-9) (4-9) IC103 AGC CONT 1,2 R,B GAIN...
Page 64
DSR-PD150/PD150P 3-2. OVERALL BLOCK DIAGRAM (2/4) ( ) : Page No. shown in ( ) indicates the page to refer on the schematic diagram. CN300 VC-242D BOARD(2/4) DV IN/OUT (4-23) (4-17) X301 24.576MHz IC301 IC1407 CN006 CN301 (4-26) SPCK SPCK...
Page 65
DSR-PD150/PD150P 3-3. OVERALL BLOCK DIAGRAM (3/4) ( ) : Page No. shown in ( ) indicates the page to refer on the schematic diagram. CN007 C MECHA DECK FOR ADJUSTMENTS (SEE PAGE 4-39) (4-28) VC-242D BOARD(3/4) RF MON IC102 REC CK...
Page 67
DSR-PD150/PD150P FRAME SCHEMATIC DIAGRAM (2/3) CN100 CN025 JK-190 BOARD LB-065D BOARD SUBB LCD903 UNIT VDDB J300 B_CCD_OUT VIDEO V2BB ND200 VDD2B BACK V2AB AUDIO LIGHT J301 CN300 J302 J303 R_CCD_OUT S-VIDEO DV IN/OUT LANC VDD2R CONTINUED ON V2BR V2AR (SEE PAGE...
Page 68
DSR-PD150/PD150P FRAME SCHEMATIC DIAGRAM (3/3) FP-197 CONTROL SWITCH FP-194 BLOCK(ED-4980) FLEXIBLE FLEXIBLE S001 ND901 BACK-LIGHT (RVS) S001 CONTROL S002 DIAL COLOR MENU (OPEN/CLOSE) LCD901 UNIT INVERTER UNIT CN253 SP901 SPEAKER CN251 CN2100 CK-093 BOARD PANEL_B PANEL_B CN250 PANEL_G PANEL_G P_UNREG_GND...
Page 69
DSR-PD150/PD150P DSR-PD150/PD150P 4-2. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS THIS NOTE IS COMMON FOR WIRING BOARDS AND SCHEMATIC DIAGRAMS (In addition to this, the necessary note is printed in each block) (For printed wiring boards) (Measuring conditions voltage and waveform) •...
Page 70
R103 C105 4700 4.7u L105 100uH C108 R111 6.3V R110 C110 NTSC MODEL:DSR-PD150 R105 4.7u PAL MODEL :DSR-PD150P 5600 IC105 Precautions Upon Replaching CCD imager BUFFER IC100 IC105 • The CD-254 board mounted as a repair part is not equipped AD8014ART-REEL7 with a CCD imager.
Page 71
DSR-PD150/PD150P CD-254 (CCD IMAGER) PRINTED WIRING BOARD — Ref. No. CD-254 Board; 1,000 Series — For printed wiring board • Refer to page 4-118 for parts location. • This board is four-layer print board. However, the pat- terns of layers two and three have not been included in the diagram.
Page 72
DSR-PD150/PD150P For Schematic Diagram • Refer to page 4-51 for printed wiring board. • Refer to page 4-113 for waveforms. VC-242D BOARD(1/18) S/H AGC,TG(CA(CH)BLOCK) C758 C719 C720 -REF.NO.:10000 SERIES- 0.1u 0.1u 1608 XX MARK:NO MOUNT NO MARK:REC/PB MODE C723 C725 R708 0.1u...
Page 73
DSR-PD150/PD150P For Schematic Diagram • Refer to page 4-51 for printed wiring board. • Refer to page 4-114 for waveform. VC-242D BOARD(2/18) SIGNAL PATH CAMERA SIGNAL PROCESS(CA(U-C)BLOCK) NO MARK:REC/PB MODE VIDEO SIGNAL R :REC MODE -REF.NO.:10000 SERIES- P :PB MODE...
Page 74
DSR-PD150/PD150P For Schematic Diagram • Refer to page 4-51 for printed wiring board. VC-242D BOARD(3/18) MS I/F(MS-1 BLOCK) -REF.NO.:10000 SERIES- XX MARK:NO MOUNT D_2.8V TO(18/18) FB1404 C1416 IC1403 6.3V 16Mbit DRAM IC1403 SPCK TO(4/18) MSM51V18160DSL-6LFS1 DRD15 DQ16 DRD0 DRD1 DRD14...
Page 75
DSR-PD150/PD150P For Schematic Diagram • Refer to page 4-51 for printed wiring board. • Refer to page 4-114 for waveform. VC-242D BOARD(4/18) RS-232C I/F STILL CONTROL D_2.8V (MS-2 BLOCK) TO(18/18) REG_GND -REF.NO.:10000 SERIES- IC1404 R1450 100k XX MARK:NO MOUNT R1446...
Page 76
DSR-PD150/PD150P For Schematic Diagram • Refer to page 4-51 for printed wiring board. • Refer to page 4-114 for waveform. IC1411 VC-242D BOARD(5/18) X1402 20MHz MS DRV MS DRIVE(MS-3 BLOCK) NO MARK:REC/PB MODE R :REC MODE IC1411 -REF.NO.:10000 SERIES- TC7SU04FU(TE85R)
Page 77
DSR-PD150/PD150P For Schematic Diagram • Refer to page 4-51 for printed wiring board. • Refer to page 4-114 for waveforms. VC-242D BOARD(6/18) NO MARK:REC/PB MODE DV SIGNAL PROCESS(JC-1 BLOCK) XACC SIGNAL PATH R :REC MODE XACC P :PB MODE XENA -REF.NO.:10000 SERIES-...
Page 78
DSR-PD150/PD150P For Schematic Diagram • Refer to page 4-51 for printed wiring board. VC-242D BOARD(7/18) SIGNAL PATH NO MARK:REC/PB MODE DV INTERFACE(JC-2 BLOCK) VIDEO SIGNAL R :REC MODE AUDIO P :PB MODE -REF.NO.:10000 SERIES- CHROMA Y/CHROMA SIGNAL XX MARK:NO MOUNT FB302 D_1.9V...
Page 79
DSR-PD150/PD150P For Schematic Diagram • Refer to page 4-51 for printed wiring board. • Refer to page 4-114 for waveforms. VC-242D BOARD(8/18) NO MARK:REC/PB MODE REC/PB AMP(RF BLOCK) R :REC MODE P :PB MODE -REF.NO.:10000 SERIES- XX MARK:NO MOUNT TO(18/18) TRF_2.8V...
Page 80
DSR-PD150/PD150P For Schematic Diagram • Refer to page 4-51 for printed wiring board. • Refer to page 4-114 for waveforms. VC-242D BOARD(9/18) LINE IN/OUT(IO BLOCK) NO MARK:REC/PB MODE R :REC MODE TO(1/18,10/18, A_4.6V 18/18) -REF.NO.:10000 SERIES- FB1301 P :PB MODE D_2.8V...
Page 81
DSR-PD150/PD150P For Schematic Diagram • Refer to page 4-51 for printed wiring board. • Refer to page 4-114 for waveforms. VC-242D BOARD(10/18) LINE A/D(IN BLOCK) NO MARK:REC/PB MODE -REF.NO.:10000 SERIES- R :REC MODE XX MARK:NO MOUNT P :PB MODE TO(3/18,...
Page 82
DSR-PD150/PD150P For Schematic Diagram • Refer to page 4-51 for printed wiring board. • Refer to page 4-115 for waveforms. VC-242D BOARD(11/18) RGB DRIVE/TG(VF BLOCK) -REF.NO.:10000 SERIES- XX MARK:NO MOUNT L1803 C1812 C1814 10uH 3.3u 0.1u B NO MARK:REC/PB MODE...
Page 83
DSR-PD150/PD150P For Schematic Diagram • Refer to page 4-51 for printed wiring board. • Refer to page 4-115 for waveform. VC-242D BOARD(12/18) CAMERA CONTROL(CA(MC) BLOCK) NO MARK:REC/PB MODE R :REC MODE -REF.NO.:10000 SERIES- P :PB MODE XX MARK:NO MOUNT CN004...
Page 84
DSR-PD150/PD150P For Schematic Diagram • Refer to page 4-51 for printed wiring board. • Refer to page 4-115 for waveform. VC-242D BOARD(13/18) MECHANISM CONTROL(MC BLOCK) NO MARK:REC/PB MODE -REF.NO.:10000 SERIES- REG_GND C506 C508 R :REC MODE XX MARK:NO MOUNT 0.01u...
Page 85
DSR-PD150/PD150P For Schematic Diagram • Refer to page 4-51 for printed wiring board. • Refer to page 4-115 for waveforms. VC-242D BOARD(14/18) NO MARK:REC/PB MODE DRUM/CAPSTAN MOTOR DRIVE(MD BLOCK) R :REC MODE P :PB MODE -REF.NO.:10000 SERIES- XX MARK:NO MOUNT...
Page 86
DSR-PD150/PD150P DSR-PD150/PD150P FP-594 (LOADING MOTOR, S/T REEL SENSOR) PRINTED WIRING BOARD — Ref. No. FP-594 Flexible Board; 2,000 Series — FP-594 BOARD M902 LOADING MOTOR SENSOR S903 MODE SW Q901 Q902 TAPE END TAP E TOP S901 C IN S902 REC.P...
Page 87
DSR-PD150/PD150P For Schematic Diagram • Refer to page 4-51 for printed wiring board. • Refer to page 4-115 for waveforms. VC-242D BOARD(15/18) R006 R005 R004 R003 R002 TO(18/18) TO(18/18) 6800 3300 1500 1200 HI CONTROL(HI BLOCK) D007 Q1101 MA8082-(K8).S0 2SD2216J-QR(K8).SO NO MARK:REC/PB MODE -REF.NO.:10000 SERIES-...
Page 88
DSR-PD150/PD150P For Schematic Diagram • Refer to page 4-51 for printed wiring board. • Refer to page 4-115 for waveforms. VC-242D BOARD(16/18) AU LINE A/D,D/A NO MARK:REC/PB MODE R :REC MODE -REF.NO.:10000 SERIES- IC1003 P :PB MODE XX MARK:NO MOUNT...
Page 89
DSR-PD150/PD150P For Schematic Diagram • Refer to page 4-51 for printed wiring board. VC-242D BOARD(17/18) LINE AMP -REF.NO.:10000 SERIES- G_CONT_VCC TO(16/18) XX MARK:NO MOUNT C1079 R1076 R1077 NO MARK:REC/PB MODE ± 0.5% 1608 R :REC MODE P :PB MODE C1055 0.47u...
Page 90
DSR-PD150/PD150P For Schematic Diagram • Refer to page 4-51 for printed wiring board. VC-242D BOARD(18/18) CONNECTOR(CN BLOCK) -REF.NO.:10000 SERIES- XX MARK:NO MOUNT CN023 LCH1IN RCH2IN TO(16/18) L(CH1)IN R(CH2)IN TO(16/18) REG_GND REG_GND CN021 TO(12/18) EXT_MIC_DET EXT_MIC_DET EXT_MIC_MONO XMIC_MONO TO(12/18) REG_GND REG_GND...
Page 91
DSR-PD150/PD150P JK-190 (JACK BOARD) PRINTED WIRING BOARD — Ref. No. JK-190 Board; 2,000 Series — DV IN/OUT For printed wiring board VC-242D • Refer to page 4-120 for parts location. S/H AGC, TG, CAMERA SIGNAL PROCESS, MS I/F, RS232C I/F, STILL CONTROL, MS DRIVE, •...
Page 92
DSR-PD150/PD150P SIGNAL PATH JK-190 BOARD VIDEO SIGNAL JACK BOARD AUDIO -REF.NO.:2000 SERIES- CHROMA Y/CHROMA SIGNAL XX MARK:NO MOUNT J301 FB300 FB301 CN301 S VIDEO LANC_GND/232C_TD LANC_GND/232C_TD R311 HP_JACK_IN XSJACK_IN LANC_SIG/232C_RD LANC_SIG/232C_RD S_C_I/O R312 HP_R_OUT XLANC_JACK_IN S_Y_I/O R313 HP_L_OUT XLANC_JACK_IN LANC_DC...
Page 93
DSR-PD150/PD150P CK-093 (KEY IN) PRINTED WIRING BOARD — Ref. No. CK-093 Board; 1,000 Series — TC/U-BIT For printed wiring board LB-065D MA-386D • Refer to page 4-120 for parts location. XM-001 (AUDIO AMP) (BACK LIGHT) CK-093 (MIC AMP) (KEY IN) •...
Page 95
DSR-PD150/PD150P PD-126 (RGB DRIVE/TG) PRINTED WIRING BOARD — Ref. No. PD-126 Board; 20,000 Series — FP-194 FLEXIBLE BOARD S001 S001 MENU 1-678-061- FP-197 FLEXIBLE BOARD S002 (OPEN/CLOSE) 1-678-064- S001 (RVS) For printed wiring board LB-065D MA-386D • Refer to page 4-120 for parts location.
Page 96
DSR-PD150/PD150P For Schematic Diagram • Refer to page 4-116 for waveforms. PD-126 BOARD L2105 Note : Resistor is mounted to the Location where C2129 is printed. RGB DRIVE/TG L2103 10uH R2161 2520 -REF.NO.:20000 SERIES- C2115 XX MARK:NO MOUNT 3.3u R2165...
Page 97
DSR-PD150/PD150P LA-026 (ZOOM/FOCUS DRIVE, VAP DRIVE, KEY IN/CONNECTOR) PRINTED WIRING BOARD — Ref. No. LA-026 Board; 20,000 Series — For printed wiring board VC-242D • Refer to page 4-121 for parts location. S/H AGC, TG, CAMERA SIGNAL PROCESS, MS I/F, RS232C I/F, STILL CONTROL, MS DRIVE, •...
Page 98
DSR-PD150/PD150P For Schematic Diagram • Refer to page 4-75 for SE-108 printed wiring board. LA-026 BOARD(1/3) ZOOM/FOCUS DRIVE(LA BLOCK) -REF.NO.:20000 SERIES- XX MARK:NO MOUNT NO MARK:REC/PB MODE HALL_AD TO(3/3) SE-108 BOARD R :REC MODE P :PB MODE SE603 VAP SENSOR -REF.NO.:1000 SERIES-...
Page 99
DSR-PD150/PD150P For Schematic Diagram • Refer to page 4-67 for printed wiring board. LA-026 BOARD(2/3) Q071 Q070 R5.1/P0 2SB1462J-QR(K8).SO 2SB1462J-QR(K8).SO VAP DRIVE(LD BLOCK) R085 IC072 IC072 Q070,071 -REF.NO.:20000 SERIES- 1/8W LB1830M-TLM PROTECT C076 VAP DRIVE Q076 XX MARK:NO MOUNT 2SA1588-OY-TE85L R5.1/P0...
Page 100
DSR-PD150/PD150P For Schematic Diagram • Refer to page 4-67 for printed wiring board. LA-026 BOARD(3/3) KEY IN/CONNECTOR NO MARK:REC/PB MODE R :REC MODE -REF.NO.:20000 SERIES- P :PB MODE XX MARK:NO MOUNT FP-189 FLEXIBLE CN054 FADER FADER BACK_LIGHT BACK_LIGHT SPOT_LIGHT SPOT_LIGHT LND051 N.C.
Page 101
DSR-PD150/PD150P SE-108 (VAP SENSOR) PRINTED WIRING BOARD — Ref. No. SE-108 Board; 1,000 Series — For printed wiring board FP-188 FLEXIBLE BOARD FP-189 FLEXIBLE BOARD • Refer to page 4-121 for parts location. • This board is six-layer print board. However, the pat-...
Page 103
8. HRS METER (Hours meter) The data of “HRS METER” of the menu are memorized in addresses 00 to 13 of page A. (VC-242D board IC1105 (EEPROM)). When replacing the drum assy. capstan motor or mechanism deck, reset the data of the addresses corresponding to the replaced parts to “00”. Note: Same data is memorised in two addresses, so be sure to reset both addresses.
DSR-PD150/PD150P SECTION 6 REPAIR PARTS LIST 6-1. EXPLODED VIEWS NOTE: • -XX, -X mean standardized parts, so they may • The mechanical parts with no reference number The components identified by mark 0 or have some differences from the original one.
CD-254 CK-093 6-2. ELECTRICAL PARTS LIST NOTE: • Due to standardization, replacements in the • COILS When indicating parts by reference number, parts list may be different from the parts uH: µH please include the board name. specified in the diagrams or the components •...
Page 140
〈 〉 FOR CAMERA COLOR REPRODUCTION ADJUSTMENT Take a copy of CAMERA COLOR REPRODUCTION FRAME with a clear sheet for use. DSR-PD150/PD150P — 329 —...