Table of Contents
Advertisement
JVC
AUDIO/VIDEO
CONTROL RE
RX-5020VBK / RX-5022VSL
d_
°°
@
I,I I
I
1,1_
f_l"_ill_l
I I I&llf
v_/Irl/-
¥
k11111,
////Remote#//
DIGITAL
SURROUND
Drlr_
DIGITAL
)-.a:_e] ImEoI_o,]
|toni
INSTRUCTIONS
For Customer
Use:
Enter below the Model No. and Serial
No. which are located either on the rear,
bottom or side of the cabinet. Retain this
information for future reference.
Model No.
Serial No.
LVT0850-001A
[J]
Advertisement
Table of Contents
Related Manuals for JVC RX-5022VSL
Summary of Contents for JVC RX-5022VSL
- Page 1 AUDIO/VIDEO CONTROL RE RX-5020VBK / RX-5022VSL f_l"_ill_l I I I&llf v_/Irl/- ¥ k11111, ////Remote#// DIGITAL °° I,I I 1,1_ SURROUND Drlr_ DIGITAL )-.a:_e] ImEoI_o,] |toni INSTRUCTIONS For Customer Use: Enter below the Model No. and Serial No. which are located either on the rear, bottom or side of the cabinet.
- Page 2 For Canada/pour le Canada CAUTION: PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT ATTENTION: POUR EVITER CHOCS ELECTRIQUES, CAUTION: TO REDUCE RISK OF ELECTRIC SHOCK. INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS DO NOT REMOVE COVER...
-
Page 3: Table Of Contents
Pro Logic II, Dolby Digital DTS Digital Surround ............Using DAP Modes and All Channel Stereo ......COMPU LINK Remote Control System ..Operating JVC's Audio/Video Components .......... Operating Audio Components ..........Operating Video Components ..........Operating Other Manufacturers' Video Equipment .......... -
Page 4: Table Of Contents
Parts identification pages in the parentheses for details. Front Panel STANDBY/ON O11 button and STANDBY lamp (8) FM/AM TUNING UP/DOWN buttons (16) FM/AM PRESET UP/DOWN buttons (16, FM MODE button (17) MEMORY button (16, Display ADJUST button (15, 22, 23) Remote sensor SETTING... -
Page 5: Getting Started
Getting Started I"_ I :I_I_ I ll!lii41i[!+ "D General Precautions Before using the remote control, put two supplied batteries first. ¢D • When using the remote control, aim the remote control directly • DO NOT insert any metal object into the unit. the remote sensor on the unit. - Page 6 Getting Started AM Loop Antenna Outdoor FM antenna (not supplied) (supplied) If FM reception is poor, connect outdoor FM antenna. Standard type Supplied FM outdoor FM antenn_ antenna (not supplied) FM antenna (supplied) Extend the supplied FM antenna horizontally. If AM reception is poor, connect outdoor single vinyl-covered wire (not supplied).
- Page 7 Speaker layout diagram [_ _'t_-_ __'_ "YES" for the subwoofer and "SMALL" for the front, center After connecting the front, center, rear speakers and/or a subwoofer, and rear speakers are initial settings. To get best possible set the speaker setting information properly to obtain the best sound, change the subwoofer and speaker settings to fit your possible Surround effect.
- Page 8 Getting Started Cassettedeckor CD recorder Cassette deck To audio input To audio output You can connect the following audio/video components to this receiver. Refer also to the manuals supplied with your components. Audio Components Video Components • CD player* • TV* •...
- Page 9 IMPORTANT: • When connecting the DVD player or digital TV using the digital terminal, you also need to connect it to the video jack on the rear. Without connecting it to the video jack, you can view no playback picture. •...
-
Page 10: Basic Operations
Basic Operations Front Panel Select the DVD player. [.m [_,"L_I I_ Select the VCR. TV SOUND Select the TV sound (or the CATV converter). Press STANDBY/ON ©/I (or STANDBY/ON ©/I AUDIO on the CD * Select the CD player. remote control). -
Page 11: Master Volume
Selecting different sources for picture sound You can watch picture from a video component while listening You must turn off the speakers when you listen with headphones. ¢D sound from another component. Connect a pair of headphones to the PHONES jack on the front Press one of the audio source selecting... - Page 12 Basic Operations Basic adjustment auto memorv This receiver memorizes sound settings for each source when: ONLY • you turn off the power, • you change the source, and Press MUTING on the remote control to mute MUTING • you assign the source name. the sound through all speakers and headphones connected.
-
Page 13: Basic Settings
Basic Settings €1 t,.¢l When you use the digital input terminals, register what components When you have connected digital source components using both the are connected to which terminals (DIGITAL 1/2) so that the correct analog connection (see page 6) and the digital connection (see page source name will appear when you select the digital... - Page 14 Basic Settings To obtain the best possible sound or effect from the Surround modes (see page 18), register the following speakers and subwoofer information after all connections are completed. ANALOG The followings are items you can set: : Select this for the analog input mode. •...
- Page 15 Speaker distance Speaker size Register the sizes of all the connected speakers. Register the unit you use, then the speaker distance from your ° When you change your speakers, register the information about listening point. ° If you have set the unit before, start from step 3 the speakers again.
- Page 16 Basic Settings Crossover frequency Low frequency effect attenuator Small speakers cannot reproduce the bass sounds efficiently. If you If the bass sound is distorted while playing back software using Dolby Digital or DTS Digital Surround, follow the procedure use a small speaker in any position, this receiver automatically...
-
Page 17: Sound Adjustments
Sound Adiustments i" ¢D Once each of following settings has been adjusted, this receiver Press ADJUST repeatedly until "BASS" *DJOST memorizes the adjustment for each source. or "TREBLE" (with the current setting)* appears on the display. * "0" is the initial setting. If you have already changed the setting, another number (level) will be shown. -
Page 18: Tuner Operations
Tuner Operations I_V_lWtt!'l_l[] 11Jl[--_ Press FM/AM to select the band Once a station is assigned to a channel number, the station can be quickly tuned. You can preset up to 30 FM and 15 AM stations. (FM or AM). The last received station of the selected band is tuned in. - Page 19 Press MEMORY again while the ..selected channel number is flashing _x-_ When an FM stereo broadcast is hard to receive or noisy, you can on the display. change the FM reception mode while receiving an FM broadcast. The selected channel number stops flashing.
- Page 20 Dolby Digital* You can use the following Surround modes to reproduce a realistic sound field: Used to reproduce multichannel sound tracks of the software • Dolby Surround encoded with Dolby Digital ( ,[1_ • Dolby Pro Logic II • To enjoy the software encoded with Dolby Digital,...
- Page 21 • All Channel Stereo • DAP (Digital Acoustic Processor) modes ¢D DAP modes have been designed to create important acoustic This mode can reproduce a larger stereo sound field using all the surround elements. connected (and activated) speakers. All Channel Stereo can be used when the front and rear The sound heard in a live club, dance club, hall or pavilion consists ¢D...
-
Page 22: Creating Realistic Sound Fields
Creating Realistic Sound Fields Available Surround modes will vary depending on how many speakers are used with this receiver. Make sure that you have set the speaker information correctly (see pages 12 to 14). • If only front speakers are connected, you cannot use Surround modes. - Page 23 Before you start, remember... ° Make sure that you have set the speaker information correctly (see pages 12 to 14). • You cannot adjust the center speaker output level when you have set "CNTR SP" to "NONE." • You cannot adjust the rear speaker output levels when you have set "REAR SP"...
- Page 24 Creating Realistic Sound Fields 3 Press SOUND. 3 Adjust the speaker output levels. The 10 keys are activated for sound adjustments. I) Press ADJUST repeatedly until one ADJUST of the following indications (with the _'_ Press TEST to check if you can hear the TEST current setting)* appears...
- Page 25 so..oo.oo.,o,, 2 Press SURROUND ON/OFF ll_-llil!+ r...] activate Surround mode. Once you have adjusted the DAP modes and All Channel Stereo, When the Surround mode turns on, the last adjustment is memorized for each source. selected Surround mode will be activated. •...
-
Page 26: Compu Link Remote Control System
Automatic PowerOn/Off(Standby): o nlypossible with the The COMPU LINK remote control system allows you to operate COMPULINK-3andCOMPU LINK-4 JVC's audio components through the remote sensor on the receiver. To use this remote control system, you need to connect JVC's audio... - Page 27 SOUND, you can use the following buttons for sound • You need to connect JVC's audio components through the COMPU adjustment: LINK (SYNCHRO) jacks (see page 24) in addition to the connections using cables with RCA pin plugs (see page 6).
- Page 28 Cassette deck CD changer After pressing CD-DISC, you can use the following buttons for CD After pressing TAPE/CDR, you can use the following buttons for changer operations: cassette deck operations: I-4-4 : Return to the beginning of the current : Fast wind the tape from left to right. (or previous) track.
- Page 29 To operate JVC's video components using this remote control: fNTfR -" 11ilii 'ooi { ii+ • Some JVC's VCRs can accept two types of the control signals-- ,lii) _W'_; i11 )u[il remote code "A" and "B." Before using this remote control, make sure that the remote control code of the VCR connected to the VCR jacks is set to code "A."...
- Page 30 To change the transmittable signals for By changing the transmittable signals, you can use the remote control supplied for this unit to operate other manufacturers' operating a CATV converter equipment. • Refer also to the manuals supplied with the other products. I Set TV/CATV selector to CATV.
- Page 31 To change the transmittable signals for To change the transmittable signals for operating a VCR operating a DVD player I Press and hold STANDBY/ON O/I VCR. I Press and hold STANDBY/ON ©/I DVD. Press VCR. 2 Press DVD. ;3 Enter manufacturer's code using buttons 1-9, ;3 Enter manufacturer's...
-
Page 32: Troubleshooting
Use this chart to help you solve daily operational problems. If there is any problems you cannot solve, contact your JVC's service center. The power does not come on. The power cord is not plugged Plug the power cord into an AC outlet. - Page 33 Amplifier Output Power At Stereo operation: €0 100 W per channel, rain. RMS, driven into 8 n, Front channels: 40 Hz to 20 kHz with no more than 0.8% total harmonic distortion. At Surround operation: €o Front channels: 100 W per channel, min.
-
Page 34: Specifications
Specifications FM tuner (IHF) 87.5 MHz to 108.0 MHz Tuning Range: 12.8 dBf (1.2 taV/75 _) Monaural: Usable Sensitivity: 21.3 dBf (3.2 laV/75 _2) Monaural: 50 dB Quieting Sensitivity: 41.3 dBf (31.5 [aV/75 _) Stereo: 78 dB at 85 dBf Monaural: Signal-to-Noise Ratio (IHF-A... - Page 35 Authorized Service Centers QUALITY SERVICE HOW TO LOCATE YOUR JVC SERVICE CENTER TOLL FREE: 1 (808) 537-5722 http://www.jvc.com Dear Customer, In order to receive the most satisfaction from your purchase, please read the instruction booklet before operating the unit. In the event that repairs are necessary,...
- Page 36 SERVICE: * Return your product to a JVC authorized service center with a copy of your bill of sale. For your nea rest JVC authorized * service center, please call toll free: (800) 537-5722. * If service is not available...
- Page 37 VICTOR COMPANY OF JAPAN, LIMITED 1201NHMMDWJEIN...
- Page 38 " .." Supercede r'l Total pages scanned= _F_-_q_ InitialandDateeachsectionbelowasitiscompleted: soo° i ,°°o. I I Po.e°l I Batched 6,-/7 # Of Models" L0206151 Figure Properties Batch #: Title Chassis Type Product s_v_l_/! OWNM [] _=PP-R [] TECHM [] INSTL [] PROC [] SALES [] Doc Type Doc Class Code Date Received...