Related Manuals for Black & Decker BDXTTSM1
Summary of Contents for Black & Decker BDXTTSM1
- Page 1 BDXTTSM1 Smart Thermostat Installation & Operation Manual Please read before returning this product for any reason.
- Page 2 USING THIS MANUAL BEFORE INSTALLING AND USING THE BDXTTSM1 SMART THERMOSTAT, please read these instructions carefully. This manual is intended as a reference guide for the installation, configuration, and operation of your device. Save all instructions in a safe place for future reference.
- Page 3 IMPORTANT SAFETY INSTRUCTIONS WARNING: Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. WARNING: Never modify this product. Damage or personal injury could result. WARNING: • Follow all applicable electrical codes and regulations regarding the installation or replacement of a thermostat in the local jurisdiction.
- Page 4 IN THE BOX ........... . 1 INSTALLING THE BDXTTSM1 SMART THERMOSTAT ....2 DEVICE OVERVIEW .
- Page 5 For further information needed on its features, please visit www.ctnovatech.com for frequently asked questions and the electronic manual. ©2021 CT Nova US LLC 4700 Duke Drive Suite 200, Mason, OH 45040, USA IN THE BOX Wall Plate (if required) Mounting Hardware BDXTTSM1 Smart Thermostat with Mounting Plate Installation & Operation Manual...
- Page 6 INSTALLING THE THERMOSTAT There are 5 steps to install the BDXTTSM1 Smart Thermostat. 1. Determine Wiring Configuration 2. Remove Old Thermostat 3. Install Thermostat Mounting Base 4. Connect Wires 5. Attach Display TOOLS REQUIRED (Not included) The following tools may be required for installation: •...
- Page 7 INSTALLING THE THERMOSTAT DETERMINE WIRING CONFIGURATION If the BDXTTSM1 Smart Thermostat is being installed in a new system or if wiring changes are required, refer to Appendix A for the wiring configurations and skip to “Install Mounting Plate”. When replacing a thermostat and replication of the existing wiring is desired on the BDXTTSM1 Thermostat, the following applies: •...
- Page 8 Wrap wires around a pencil or similar object to prevent them from falling into the wall void. The BDXTTSM1 Thermostat IS NOT COMPATIBLE with supply voltages above 30 VAC. If the old thermostat is connected WARNING: with thick wire and wire nuts or is labeled for voltages higher than 30 VAC, DO NOT INSTALL the Thermostat.
- Page 9 INSTALLING THE THERMOSTAT INSTALL MOUNTING PLATE (with WALL PLATE if required) Note: Use 3/16” drill for wall anchors if no stud is present. Use the included screws and wall anchors (if required) to attach the Mounting Plate to the wall, making sure the wires go through the center opening.
- Page 10 INSTALLING THE THERMOSTAT ATTACH WIRING To insert a wire, loosen the screw corresponding to the labeled socket and slide the wire into the socket. Once the wire is inserted, tighten the screw snugly. DO NOT OVERTIGHTEN the screws. Pull gently on each wire after the screw is snug to make sure it is secure. Inspect the wires for oxidation and integrity.
- Page 11 INSTALLING THE THERMOSTAT ATTACH DISPLAY TO MOUNTING PLATE Slide the display over the Mounting plate and the LCD display will illuminate.
- Page 12 DEVICE OVERVIEW BDXTTSM1 SMART THERMOSTAT KEYS DESCRIPTION BUTTON DESCRIPTION Change Increase INCREASE Fan Speed Set Point Change Decrease MODE DECREASE System Mode Set Point...
- Page 13 DEVICE OVERVIEW SPECIAL KEY FUNCTIONS KEYS TIME RESULT Briefly press + and - keys to switch between < 3 seconds Programmable and Non-programmable Thermostat. Hold + and – keys for 3 seconds to lock or unlock 3 seconds key pad. Hold the Fan and Mode keys for 3 seconds to enter 3 seconds or exit the Parameter Menu.
- Page 14 DISPLAY ELEMENTS Text display (Menu Item, Time, Date, etc.) Steady = Wi-Fi and Cloud Server connected Cloud Server/ 1 Flash = Wi-Fi connected, No Cloud connection Internet Connection 2 Flashes = No Wi-Fi or Cloud Server connection Thermostat Lock Displayed when thermostat keys are disabled. Indicator Schedule Indicator Displayed when thermostat schedule is enabled.
- Page 15 Heating/Cooling Modes – Press to change AUTOMATIC CHANGEOVER OFF – The SMARTSTAT – The SMARTSTAT will activate will not activate heating or heating or cooling appliance based cooling* on the room temperature. HEAT – The SMARTSTAT EMERGENCY HEAT – The SMARTSTAT will activate heating displays this with the element to...
- Page 16 SMART DEVICE APPLICATION The BDXTTSM1 Thermostat is designed for remote operation using a smart device application. Before setting up the thermostat, download the BLACK+DECKER HOME application on your IOS or Android device. After download- ing the application, follow the steps in the BLACK+DECKER Home...
- Page 17 This page intentionally left blank.
- Page 18 THERMOSTAT PARAMETERS To access the BDXTTSM1 Smart Thermostat menu parameters manually, hold down the Mode and Fan buttons for 3 seconds. The following is a list of the available parameters. MENU OPTIONS DESCRIPTION TEXT CON 1H 1-Stage Heating CON 2H...
- Page 19 THERMOSTAT PARAMETERS MENU OPTIONS DESCRIPTION TEXT DF 2H1C 2-Stage Heating & 1-Stage Cooling HVAC (Cont.) DF 3H2C 3-Stage Heating & 2-Stage Cooling Gas-fired equipment Fan Type Electric Electric powered equipment HP b Changeover Valve Defaults to Heating HP Type HP o Changeover Valve Defaults to Cooling Fahrenheit US Customary System of Temperature Units Temp...
- Page 20 THERMOSTAT PARAMETERS MENU OPTIONS DESCRIPTION TEXT Auto Gradually increases set point after setback. Recovery NO = Disable, YES = Enable 0.5F (0.25C) Control variable that affects thermostat response Span time. A larger number slows response time. 3.0F (1.5C) 4F / 2C Allowable temperature difference between Auto Deadband 3F / 1.5C...
- Page 21 MANUAL OPERATION MODE CHANGE To change the operating mode, press the Mode ( ) button. The following table shows the mode sequence based on the System Type: Mode Change Sequence System Type Sequence Conventional Heating/Cooling Heat Pump Dual Fuel (Gas/Electric) Available Modes Based on HVAC System Setting: System Type Heat Only...
- Page 22 APPENDIX A – SCHEMATIC WIRING The following are schematic wiring diagrams based on applicable system types. Failure to correctly wire the BDXTTSM1 Thermostat could WARNING: result in death or serious injury. The local jurisdiction may require installation by authorized service personnel.
- Page 23 APPENDIX A – SCHEMATIC WIRING Failure to correctly wire the BDXTTSM1 Thermostat could WARNING: result in death or serious injury. The local jurisdiction may require installation by authorized service personnel. Conventional Boiler / AC (Non-Heat Pump) – 2 Transformers...
- Page 24 APPENDIX A – SCHEMATIC WIRING Failure to correctly wire the BDXTTSM1 Thermostat could WARNING: result in death or serious injury. The local jurisdiction may require installation by authorized service personnel. Heat Pump – 1 Transformer...
- Page 25 This page intentionally left blank.
- Page 26 APPENDIX B - WARRANTY Three-Year Limited Warranty CT Nova warrants to the original consumer purchaser only that this product and the component parts thereof, will be free from defects in workmanship and materials. CT Nova will, repair or replace, at its sole option and discretion, this product or any defective parts. CT Nova’s liability hereunder shall be limited to repair or replacement of the defective part or parts, and such cor- rection shall constitute a fulfillment of all of CT Nova’s warranties hereunder.
- Page 27 APPENDIX B - WARRANTY LIMITATION OF REMEDIES AND DAMAGES. REPAIR OR REPLACEMENT AS PROVIDED UN- DER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER. CT NOVA SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO ATTORNEYS’ FEES AND/OR COSTS OF LITIGATION, FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT.
- Page 28 APPENDIX C - COMPLIANCE This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
- Page 29 APPENDIX C - COMPLIANCE FCC AND INDUSTRY CANADA RF Radiation Exposure statement: This equipment complies with FCC and Industry Canada RF radiation exposure limits set forth for an uncontrolled environment. This equip- ment should be installed and operated with a minimum distance of 20 centimeters between the antenna and all persons.
- Page 30 APPENDIX D - SPECIFICATIONS Model BDXTTSM1 Smart Thermostat °F or °C Temperature Units 32°F to 122°F (0°C to 50°C) Operating Temperature 14°F to 140°F (-10°C to 60°C) Storage Temperature < 90% RH Non-condensing Humidity Range 18-30 VAC, 60 Hz Power Input...
- Page 31 TRADEMARK ACKNOWLEDGEMENT BLACK+DECKER® and the BLACK+DECKER Logo are trademarks of the BLACK+DECKER Industrial Tool Co., or an affiliate thereof and are used under license. The color scheme is a trademark for BLACK+DECKER power tools & accessories. © 2020 BLACK+DECKER U.S. & Canada Only Product Distributed by: CT Nova US LLC 4700 Duke Drive Suite 200, Mason, OH 45040, USA...
- Page 32 WARNING: This product can expose you to chemicals including Styrene, which is known by the State of California to cause cancer. For more information go to www.P65Warnings.ca.gov BDXT TSM1 INSTALLATI ON & OP E RATIO N M AN UA L B+D-GM-BDXTTSM1-EN-202106 v1...