Table of Contents
Advertisement
Quick Links
Register at www.Toro.com.
Original Instructions (EN)
8-Blade, 11-Blade, or 14-Blade
EdgeSeries
Greensmaster
Unit
Model No. 04651—Serial No. 408000000 and Up
Model No. 04653—Serial No. 408000000 and Up
Model No. 04655—Serial No. 408000000 and Up
Model No. 04657—Serial No. 400000000 and Up
Form No. 3469-945 Rev A
™
Cutting Unit
®
3300 or 3400 Series Traction
*3469-945*
Advertisement
Table of Contents
Related Manuals for Toro EdgeSeries 04657
Summary of Contents for Toro EdgeSeries 04657
- Page 1 3300 or 3400 Series Traction Unit Model No. 04651—Serial No. 408000000 and Up Model No. 04653—Serial No. 408000000 and Up Model No. 04655—Serial No. 408000000 and Up Model No. 04657—Serial No. 400000000 and Up *3469-945* Register at www.Toro.com. Original Instructions (EN)
-
Page 2: Table Of Contents
Whenever you need service, genuine Toro parts, or additional information, contact an Authorized Service Contents Dealer or Toro Customer Service and have the model and serial numbers of your product ready. Figure 1 identifies the location of the model and serial numbers Safety ............... -
Page 3: Safety
Make all necessary repairs before resuming operation. • Keep all parts in good working condition and all hardware tightened. Replace all worn or damaged decals. • Use only accessories, attachments, and replacement parts approved by Toro. -
Page 4: Setup
Setup Media and Additional Parts Description Qty. Operator's Manual Read before installing and operating the cutting unit. Installing the Front Roller Loosely secure the roller to the cutting unit with the height-of-cut arm and fasteners previously removed (Figure Models 04651, 04653, and 04655 Center the roller between the height-of-cut arms. -
Page 5: Product Overview
Prior to mowing each day, or as required, verify proper your Authorized Service Dealer or authorized Toro bedknife-to-reel contact. Perform this procedure distributor or go to www.Toro.com for a list of all even though the quality of cut is acceptable. approved attachments and accessories. - Page 6 (Refer to Tip the cutting unit to expose the bedknife and the Toro Manual for Sharpening Reel and reel. Rotary Mowers, Form No. 09168SL). Note: Ensure that the nuts on the back of the...
- Page 7 If excessive contact/reel drag is evident, backlap, reface the front of the bedknife, or grind the cutting unit to achieve the sharp edges needed for precision cutting (Refer to the Toro Manual for Sharpening Reel and Rotary Mowers, Form No. 09168SL).
- Page 8 Adjusting the Rear-Roller Height For Cutting Unit Model 04657 Only • If Cutting Unit Model 04657 is used on autonomous Adjust the rear roller brackets to the desired traction unit (Model 04580AA), an unadjustable height-of-cut range by positioning the required grass-deflection bar is already installed to prevent amount of spacers below the sideplate-mounting grass clippings from interfering with detection...
-
Page 9: Adjusting The Height Of Cut
Adjusting the Height of Cut bedknife and rest the rear end of the bar onto the rear of the roller (Figure 11). Adjusting the Height-of-Cut Gauge Before adjusting the height of cut, set the height-of-cut gauge as follows: Loosen the nut on the gauge bar and set the adjusting bolt to the desired height of cut (Figure Note:... -
Page 10: Height-Of-Cut And Bedknife Selection Charts
Height-of-Cut and Bedknife Selection Charts Height-of-Cut Chart Height of Cut (mm) Height of Cut (inches) No. of Rear Spacers Universal Groomer 0.060 0.125 0.188 0.250 0.250 0.375 0.375 12.7 0.500 12.7 0.500 15.9 0.625 15.9 0.625 19.1 0.750 19.1 0.750 22.2 0.875 25.4... -
Page 11: Maintenance
Ideally, take the cutting unit to your authorized Toro distributor for service. Refer to the Service Manual for your traction unit for complete Supporting the Cutting Unit instructions, special tools, and diagrams for servicing the bedknife. - Page 12 Assembling the Bedbar Install the bedbar, positioning the mounting ears between the washers and the bedbar-adjusting screw (Figure 16). Important: Center the DPA adjusters in the bedbar ears as shown in Figure If DPA adjusters are installed against the bedbar ears, this may negatively affect the bedknife-to-reel contact.
-
Page 13: Bedknife Specifications
Bedknife Specifications Installing the Bedknife Remove the rust, scale, and corrosion from the bedbar surface and apply a thin layer of oil to the bedbar surface. Clean the screw threads. Apply never-seize compound to the screws and install the bedknife to the bedbar. g016470 Figure 17 1. - Page 14 Relief-Grinding the Reel The new reel has a land width of 0.8 to 1.2 mm (0.03 to 0.05 inches) and a 30° relief grind. When the land width gets larger than 3 mm (0.120 inch) wide, do the following: Apply a 30° relief grind on all reel blades until the land width is 0.76 mm (0.030 inch) wide (Figure g255046...
- Page 15 Checking the Top Grind Angle The angle that you use to grind your bedknives is very important. Use the angle indicator (Toro Part No. 131-6828) and the angle-indicator mount (Toro Part No. 131-6829) to check the angle that your grinder produces and then correct for any grinder inaccuracy.
-
Page 16: Backlapping The Cutting Unit
Note: Additional instructions and procedures on Backlapping are available in your traction unit Operator’s Manual and the Toro Sharpening Reel and Rotary Mowers Manual, Form Number 80-300PT. Note: For a better cutting edge, run a file across the front face of the bedknife and reel when the lapping operation is completed. - Page 17 The method of transmission shall be electronic transmittal. This machinery shall not be put into service until incorporated into approved Toro models as indicated on the associated Declaration of Conformity and in accordance with all instructions, whereby it can be declared in conformity with all relevant Directives.
- Page 18 The method of transmission shall be electronic transmittal. This machinery shall not be put into service until incorporated into approved Toro models as indicated on the associated Declaration of Conformity and in accordance with all instructions, whereby it can be declared in conformity with all relevant Directives.
- Page 19 Countries Other than the United States or Canada Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor's service or have difficulty obtaining guarantee information, contact your Authorized Toro Service Center.