hit counter code
Xerox 4235 Installation Planning Manual
  1. Manuals
  2. Brands
  3. Xerox Manuals
  4. Printer
  5. 4235
  6. Installation planning manual

Xerox 4235 Installation Planning Manual

Laser printing system
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
XEROX
Xerox 4235 Laser Printing System
Installation Planning Guide
Release 1.6
March 1996
720P88361

Advertisement

Table of Contents
loading

Related Manuals for Xerox 4235

Summary of Contents for Xerox 4235

  • Page 1 XEROX Xerox 4235 Laser Printing System Installation Planning Guide Release 1.6 March 1996 720P88361...
  • Page 2 March 1996 by Xerox Corporation. All rights reserved. Printed in the United States of America Xerox and all Xerox products mentioned in this publication are trademarks of Xerox Corporation. Copyright protection claimed includes all forms and matters of copyrightable material and information now allowed by statutory or...

  • Page 3: Safety Precautions

    In such cases, the user is responsible for the expense of correcting the interference. The 4235 LPS does not exceed the class A limits for radio noise emissions from a digital apparatus as documented in the radio interference regulations of the Canadian Department of Communications.

  • Page 4: Operational Safety

    Operational safety BE REMOVED. THERE ARE NO OPERATOR SERVICEABLE AREAS INSIDE THESE COVERS. Your Xerox equipment and supplies were designed and tested to meet strict safety requirements. These include safety agency examination, approval, and compliance with established environmental standards. Attention to the following notes ensures the continued safe operation of your equipment.
  • Page 5 60HZ, 115V 50HZ, 220V–240V XEROX 4235 LPS INSTALLATION PLANNING GUIDE The 4235 LPS is manufactured under a BS5750 quality system accepted by the British Standards Institution. The 4235 LPS is listed by Underwriters Laboratories, UL478– fifth edition [UL]. Certified by CSA, CSA22.2 NO 220 [CSA].

  • Page 6: Related Publications

    Notice Related publications Publication Xerox 4235 Laser Printing System HP LaserJet IID Emulation Quick Start Guide Xerox 4235 Laser Printing System HP LaserJet IID Emulation Reference Xerox 4235 Laser Printing System Loading and Unloading Paper and Special Stock Quick Reference...

  • Page 7: Table Of Contents

    Related publications_______________________________ vi Where to get help _________________________________ xi Software ________________________________________ 1-1 Hardware_______________________________________ 1-2 Interfaces _______________________________________ 1-5 Minimum and maximum 4235 LPS configurations_____ 1-5 XDPM fonts _____________________________________ 1-7 XDPM default fonts ______________________________ 1-7 XPPM fonts _____________________________________ 1-8 XScript fonts ____________________________________ 1-9...
  • Page 8 DataProducts 2260 interface _______________________ 6-5 Parallel system configuration options________________ 6-9 SNA/SDLC _________________________________________ 6-14 Asynchronous ______________________________________ 6-14 Bisynchronous ______________________________________ 6-14 Serial cable ________________________________________ 6-15 Unsupported SNA/SDLC and bisynchronous protocols ____ 6-15 Serial system configuration options–SNA/SDLC __________ 6-17 XEROX 4235 LPS INSTALLATION PLANNING GUIDE...
  • Page 9 VM/RSCS ______________________________________________________________ 7-8 VSE/POWER___________________________________________________________ 7-10 OS/VS1 _______________________________________________________________ 7-12 Sample SNA parameters _________________________________________________ 7-15 XEROX 4235 LPS INSTALLATION PLANNING GUIDE Serial system configuration options–asynchronous ________ 6-21 Serial system configuration options–bisynchronous _______ 6-26 Environment description __________________________ 7-2 Initialization process review _______________________ 7-2...
  • Page 10 Font ordering information________________________________________________ 8-11 Glossary Index IBM JES3 sample PARMLIB parameters _____________ 7-20 4235 LPS user interface settings ___________________ 7-20 Xerox Printer Access Facility (XPAF) _______________ 7-21 Remote Print Management Facility (RPMF)__________ 7-21 Host Forms Description Language (HFDL) __________ 7-21...

  • Page 11: Introduction

    The Xerox 4235 Laser Printing System Installation Planning Guide contains information on how to prepare for the installation of your 4235 LPS. It lists the laser printing system requirements, outlines tasks and completion times, and details decisions that you need to make before installation.
  • Page 12 Checklist 13: Serial system configuration–bisynchronous. Checklist 14: Supplies and accessories "Host computer system generation" provides guidelines for the integration and operation of the 4235 LPS in a remote job entry (RJE) network. Sample system generation parameters are also provided. "Fonts, supplies, and accessories" discusses how to order fonts, supplies, and accessories.

  • Page 13: Conventions

    (for example, "select HP IID"). Also, system defaults are shown in bold. italics Document and library names (for example, the Xerox 4235 Laser Printing System Operator Guide). References to options settings are italicized in tables. Names of screens and menus are shown in initial capitals (for example, Main Menu).
  • Page 14 INTRODUCTION XEROX 4235 LPS INSTALLATION PLANNING GUIDE...

  • Page 15: Overview

    35 pages per minute. The 4235 LPS serves as a local laser printing system through a parallel or serial interface, or as a remote printing system through a communication line. It prints jobs that are created in...
  • Page 16 Customized file storage allocations 4235/XPPM font and form load via MS-DOS formatted diskettes The 4235 LPS hardware features allow you to do the following: Print up to 35 pages per minute. Print on transparencies, labels, preprinted forms, and predrilled paper.

  • Page 17: Components

    Offset multiple print jobs so that each job stacks to the right or left of the previous job. Know when the 4235 LPS requires operator attention. The alarm indicator lights up on the user interface screen and the audible tone sounds (if enabled).
  • Page 18 Print cartridge/dry in k cartridge System power switch Print cartridge release lever Raster Output Scanner (ROS) cleaning tool System controller Figure 1-1 shows the major components of the 4235 LPS. Figure 1-1. Major components Front door Paper module handle A Paper tray 4...

  • Page 19: Minimum And Maximum 4235 Lps Configurations

    XScript only) Serial synchronous communication (SNA/SDLC or bisynchronous) (XDPM and XPPM only). The 4235 LPS has two communication ports. Only one parallel interface and one serial interface can run concurrently. For example, you cannot successfully connect two bisynchronous interfaces and SNA/SDLC interfaces or two parallel interfaces at the same time.
  • Page 20 HP LaserJet Printer Commands Language (PCL4) and prints with the same results as the HP LaserJet IID printer. The 4235 LPS is delivered with a number of system fonts permanently stored on the hard disk. Font loading utilities permit the addition of other fonts in two ways:...

  • Page 21: Xdpm Fonts

    Titan10iso–P for 60 Hz laser printing systems Titan12.5iso–P for 50 Hz laser printing systems. You select the default font on the 4235 LPS menu screens at the time of installation. You can choose one of the resident system fonts or an alternate font you have loaded onto the hard disk.

  • Page 22: Xppm Fonts

    Table 1-2. XPPM fonts XPPM fonts LO112B R112BL R212BL LO212A LO312A R312BL LO412A R412BL LO512A R512BL LO912A R912BL PO612A R612BP PO812A R812BP P1012A RA12BP P1112A RB12BP PO7TYA R7TIBP FORMS$ XEROX 4235 LPS INSTALLATION PLANNING GUIDE...

  • Page 23: Xscript Fonts

    XScript fonts XEROX 4235 LPS INSTALLATION PLANNING GUIDE If you purchased the XScript printing mode option, refer to table 1-3 for the system fonts available for printing jobs formatted for that environment. Table 1-3. XScript fonts Font family Courier Times–Roman...

  • Page 24: Hp Laserjet Iid Emulation Fonts

    Table 1-4. HP LaserJet IID emulation fonts Typeface Pitch Courier (default) Courier Bold Courier Italic LinePrinter 16.67 XEROX 4235 LPS INSTALLATION PLANNING GUIDE Point Symbol set Roman–8 (default) ECMA–94 PC–8 PC–8 D/N PC–850 Legal Roman–8 ECMA–94...

  • Page 25: File Space Allocation

    File space allocation XEROX 4235 LPS INSTALLATION PLANNING GUIDE The 4235 LPS stores files on the hard disk drive. The number of files you can store on the hard disk depends upon the storage capacity of the disk. Refer to table 1-5 for the maximum number of each file type that you can load onto the different capacity disks.
  • Page 26 OVERVIEW 1-12 XEROX 4235 LPS INSTALLATION PLANNING GUIDE...

  • Page 27: Xerox Responsibilities

    Arranges with Xerox administration to schedule a delivery date for your 4235 LPS. Assists you in placing your initial order of supplies and accessories. Installs the 4235 LPS and loads the system files onto the hard disk. Conducts operator training when the 4235 LPS installation is complete.

  • Page 28: Customer Responsibilities

    Ensure that the correct interface cable is available. Preinstallation tasks Complete the option checklists, located at the back of each chapter, and perform the required tasks before your 4235 LPS is installed. The Xerox service representative uses these checklists to configure the 4235 LPS to your operating environment.
  • Page 29 Task 8 For XPPM emulation only. Determine the requirements and appropriate method for loading 9700 resource files onto the 4235 LPS. Refer to the Xerox 4235 Laser Printing Systems XPPM PDL/DJDE Reference for more information on 9700 file transfer method.

  • Page 30: Installation Countdown Log

    Installation countdown log Use the installation countdown log in table 2–1 to help plan your 4235 LPS installation. The table summarizes the tasks you must perform and when each task should occur. Use the log as a guide to make sure you have a successful installation of your 4235 LPS.
  • Page 31 Week Tasks before install –7 Request 4235 LPS font samples Schedule the 4235 LPS delivery date –6 Order custom fonts and any modifications to existing fonts –4 Select the site Prepare the site: Space requirements Electrical requirements Telephone/telephone jack Environment requirements...
  • Page 32 Serial system configuration– Serial system configuration– Supplies and accessories Responsibility Date completed Customer/Xerox _________ _________ _________ _________ _________ _________ _________ _________ _________ _________ _________ _________ _________ _________ _________ Customer _________ Xerox _________ Xerox _________ XEROX 4235 LPS INSTALLATION PLANNING GUIDE...

  • Page 33: Assignment Of Tasks During And After Installation

    You may want to designate an individual as the person responsible for the care of your 4235 LPS, or you may want to select a number of people so you have enough operators to cover absences, such as vacations and illness.
  • Page 34 The first step in integrating the 4235 LPS is to identify it to the host computer system. Refer to the "Host computer system generation" chapter, which outlines parameters designed to integrate the 4235 LPS into a number of different host computer systems.

  • Page 35: Site Planning

    XEROX 4235 LPS INSTALLATION PLANNING GUIDE This chapter helps you to prepare for the installation of your 4235 LPS. Keep in mind that preparing for installation is a responsibility that you share with Xerox. Your Xerox representatives are available to discuss installation issues and to assist you in the completion of the site installation responsibilities.

  • Page 36: Environmental Requirements

    Find a location that meets the requirements of the stationary or mobile floor plans (figures 3–1 and 3–2). Be sure to place the 4235 LPS in a location that allows you to open paper trays and doors fully and provides adequate space for service.
  • Page 37 You may want to consider a stationary or mobile floor plan when selecting a location for your 4235 LPS. It is important that the floor surface is level regardless of the floor plan you use.
  • Page 38 SITE PLANNING 300mm (11.8”) 762mm (30.0”) Figure 3-1. Stationary floor plan 450mm (17.7”) Paper module extended 450mm (17.7”) 450 mm (17.7”) 2471mm (97.3”) 450mm (17.7”) 2253mm (88.7”) XEROX 4235 LPS INSTALLATION PLANNING GUIDE...
  • Page 39 727mm (28.7”) XEROX 4235 LPS INSTALLATION PLANNING GUIDE Figure 3-2. Mobile floor plan 2160mm (85.0”) Service Area R574.5mm (22.6”) 1258.5mm (49.5”) 1553.5mm (61.2”) SITE PLANNING 277mm (10.9”) 1353mm (53.3”) 626mm (24.6”) 574.5mm (22.7)” 450.5mm (17.7”)

  • Page 40: Electrical Requirements

    Note: The 60 Hz laser printing system requires a dedicated circuit (a circuit to which no other equipment or appliance is connected). Table 3-1 lists the electrical requirements for a 60 Hz 4235 LPS. Table 3-1. Requirements for 60 Hz laser printing system...
  • Page 41 This communications equipment may consist of devices such as modems. In general, your 4235 LPS needs a modem if it is more than 60 feet from your host computer system. For short distance connections, your 4235 LPS requires a modem eliminator or null modem.
  • Page 42 Communications requirements: Interface device: Space Modem Telephone jack Figure 3-3. Checklist 1: Site preparation Humidity (15-85%) Electrical Modem eliminator Gender changer XEROX 4235 LPS INSTALLATION PLANNING GUIDE Altitude (Sea level to 6,561 feet) (Sea level to 2,000 meters) Environmental Telephone line...

  • Page 43: Printer Setup

    Disable XEROX 4235 LPS INSTALLATION PLANNING GUIDE This chapter explains how to set up your 4235 LPS to print jobs in XDPM, XPPM, XScript, or HP LaserJet IID emulation modes. Table 4-1 lists the printer setup options for Xerox Distributed Print Mode (XDPM).
  • Page 44 Before you enable these features, have a Xerox service representative define special feed parameters. Most feed stocks perform satisfactorily without the enhancement of these settings. (Refer to the "Loading label stock" section in the Xerox 4235 Laser Printing System Problem Solving Guide for more information.)

  • Page 45: General Features

    Special feed stock in paper tray 4:* Audible alarm: Predrilled paper: Before you enable these features, have a Xerox service representative define special feed parameters. Most feed stocks perform satisfactorily without the enhancement of these settings. XEROX 4235 LPS INSTALLATION PLANNING GUIDE Figure 4-1.

  • Page 46: Printer Setup Options-Xppm

    OPRINFO=YES command is coded within the IDEN statement. Displays ITEXT and OTEXT messages on the 4235 LPS screen to notify the operator when a job requires special attention. Allows you to select the paper size used to print your forms.
  • Page 47 Enable Disable Before you enable these features, have a Xerox service representative define special feed parameters. Most feed stocks perform satisfactorily without the enhancement of these settings. (Refer to the Xerox 4235 Laser Printing System Problem Solving Guide for more information.) XEROX 4235 LPS INSTALLATION PLANNING GUIDE Table 4-2.
  • Page 48 Predrilled paper: Before you enable these features, have a Xerox service representative define special feed parameters. Most feed stocks perform satisfactorily without the enhancement of these settings. (Refer to the Xerox 4235 Laser Printing System Problem Solving Guide for more information.) Checklist 3: Printer setup options–XPPM...

  • Page 49: Printer Setup Options-Xscript

    Disable Before you enable these features, have a Xerox service representative define special feed parameters. Most feed stocks perform satisfactorily without the enhancement of these settings. (Refer to the Xerox 4235 Laser Printing System Problem Solving Guide for more information.) XEROX 4235 LPS INSTALLATION PLANNING GUIDE Table 4-3 lists the printer setup options for XScript.
  • Page 50 Special feed stock in paper tray 4:* Predrilled paper: Before you enable these features, you must have a Xerox customer service engineer define special feed parameters. Most feed stocks perform satisfactorily without the enhancement of these settings. (Refer to the Xerox 4235 Laser Printing System Problem Solving Guide for more information.) Figure 4-3.

  • Page 51: Printer Setup Options-Hp Laserjet Iid Emulation

    Enable allows the 4235 LPS to print status sheets. Disable does not allow the 4235 LPS to print status sheets. Enable on error only allows the 4235 LPS to print status sheets as errors are encountered. Invert simplex pages is used when printing simplex jobs on predrilled/preprinted paper.
  • Page 52 Enable Disable Before you enable these features, you must have a Xerox customer service engineer define special feed parameters. Most feed stocks perform satisfactorily without the enhancement of these settings. (Refer to the Xerox 4235 Laser Printing System Problem Solving Guide for more information.) The HP LaserJet IID emulation does not recognize the Predrilled paper option in General Features.
  • Page 53 Predrilled paper:** Before you enable these features, have a Xerox service representative define special feed parameters. Most feed stocks perform satisfactorily without the enhancement of these settings. Refer to the Xerox 4235 Laser Printing System Problem Solving Guide for more information.
  • Page 54 PRINTER SETUP 4-12 XEROX 4235 INSTALLATION PLANNING GUIDE...

  • Page 55: Document Formatting

    XDPM, XPPM, XScript, or HP LaserJet IID emulation environments. Table 5–1 lists the document formatting options for Xerox Distributed Print Mode (XDPM). Based on your choices, complete Checklist 6: Document formatting options–XDPM (figure 5–1).
  • Page 56 , enter the desired tab values. The default interval is 132 pixels per tab. The 4235 LPS has one set of default tab stops for each page size and font orientation. There are 32 tab stops. XEROX 4235 LPS INSTALLATION PLANNING GUIDE...
  • Page 57 Enable User defined key Disable character Enable XEROX 4235 LPS INSTALLATION PLANNING GUIDE XDPM document formatting options (continued) Description Select fixed or variable vertical tab settings. If you select variable , enter the desired tab values. If fixed tab stops is selected as the default tab stop option, you...
  • Page 58 Enter new tab values:_________________ Variable Millimeters Enter new tab values: ________________ Single Triple Disable Duplex Head–to–toe No shift Millimeters Disable Disable XEROX 4235 LPS INSTALLATION PLANNING GUIDE Mixed Pixels Other:____________ Other:____________ Other:____________ Other:____________ Pixels Pixels One and one–half Other Pixels...

  • Page 59: Document Formatting Options-Xppm

    Form merge/form Enable Disable XEROX 4235 LPS INSTALLATION PLANNING GUIDE Table 5–2 lists the document formatting options for Xerox Production Print Mode (XPPM). Based on your choices, complete Checklist 7: Document formatting options–XPPM (figure 5–2). Your Xerox service representative uses the checklist during installation.
  • Page 60 Job Descriptor library (JDL): Job Descriptor entry (JDE): Form merge/form: 5–6 Checklist 7: Document formatting options–XPPM 9ASC other:_______________ LAND other:_______________ Enable Disable Form name ___________________ 9ASC other: ______________________ LAND other: ______________________ Enable Disable Form name ____________________ XEROX 4235 LPS INSTALLATION PLANNING GUIDE...

  • Page 61: Document Formatting Options-Xscript

    Simplex printing Duplex – Regular Duplex – Tumbled XEROX 4235 LPS INSTALLATION PLANNING GUIDE Table 5–3 lists the document formatting options for XScript. Based on your choices, complete Checklist 8: Document formatting options–XScript (figure 5–3). Your Xerox service representative uses the checklist during installation.
  • Page 62 Tray 3 Paper cassette currently loaded) Tray 4 8.5" x 11"/216 x 279 mm or A4 (8.27" x 11.69"/210 x 297 mm) High capacity stacker Top output tray Simplex Duplex – Regular Duplex – Tumbled XEROX 4235 LPS INSTALLATION PLANNING GUIDE...

  • Page 63: Document Formatting Options-Hp Laserjet Iid Emulation

    Table 5–4 lists the document formatting options for HP LaserJet IID emulation. Based on your choices, complete Checklist 9: Document formatting options–HP LaserJet IID emulation (figure 5–4). Your Xerox service representative uses the checklist during installation. HP LaserJet IID emulation document formatting options...
  • Page 64 This setting defines the default page orientation as portrait or landscape. This setting defines the default form length. You may specify from 5 up to 128 lines. The default form length is 60 lines. XEROX 4235 LPS INSTALLATION PLANNING GUIDE...
  • Page 65 Long edge binding Input tray: Tray 1 Paper size: Letter Orientation: Portrait Form Length: 60 lines XEROX 4235 LPS INSTALLATION PLANNING GUIDE Checklist 9: Document formatting options–HP LaserJet IID emulation ROMAN–8;F;10.0;12.0;Upright;Medium;Courier;Port Other: ROMAN–8 Tray 2 Legal Landscape Other: _____________ (5–128 lines) DOCUMENT FORMATTING Other:(1–99) _____________...
  • Page 66 DOCUMENT FORMATTING 5–12 XEROX 4235 LPS INSTALLATION PLANNING GUIDE...

  • Page 67: System Configuration

    You must complete checklist 10 and either checklist 11, 12, or 13, depending on your choice of serial interface. The 4235 LPS receives data from a host computer system through a parallel and serial interface. Only one parallel and one serial interface can run concurrently. For example, you cannot successfully connect the bisynchronous and SNA/SDLC or two parallel interfaces at the same time.

  • Page 68: Parallel Interface Information

    You need to order a Centronics or DataProducts parallel cable to connect your host computer system to the 4235 LPS. If you do not have one, contact your Xerox sales representative to order one. To make sure the cable is available on the day of installation, place the order approximately four weeks prior to the installation date.
  • Page 69 The main control signals are BUSY, SELECT, and FAULT. At power–up, BUSY is at logic one, and SELECT and FAULT are at logic zero. BUSY indicates that the 4235 LPS cannot receive data (normally, BUSY cycles from logic zero to one and back to zero again once for every byte received).
  • Page 70 This name indicates the frame ground. This is the 4235 LPS indicator for a laser printing system fault (for example: paper jam, dry ink out, and so forth). The following pins are not used: 15, 33, 34, 35, 36.

  • Page 71: Dataproducts 2260 Interface

    However, received signals should be recognized as low signals if the voltage is +0.8 V or less. The 4235 LPS interface requires up to –2.6 ma at +2.4 V for a high output signal and requires up to 14 ma for a low output signal.
  • Page 72 4235 LPS powered off 4235 LPS taken offline from system controller. When any of these conditions occur, the 4235 LPS continues to spool the data to the print file. If you do not correct the fault condition and the print file becomes full, DEMAND changes to logic zero and data receipt is suspended until you clear the fault.
  • Page 73 Data 1 through Data 8: Input data levels. A high represents ONE; a low represents ZERO. A 0.5 microsecond pulse (minimum) used to clock data from the processor to the 4235 LPS logic. Indicates that the system controller is capable of receiving a character.
  • Page 74 1 microsecond after DEMAND and dropped within 5 microsecond s. DEMAND may stay low longer than 20 microsecond s if a fault occurs or the 4235 LPS buffer (512 bytes) is full. 0 (zero) and +5VDC (nominal), TTL (SN 74LS00 series) A high signal is defined as a voltage in the range of +2.4V to...

  • Page 75: Parallel System Configuration Options

    Parallel system configuration options XEROX 4235 LPS INSTALLATION PLANNING GUIDE Table 6–3 lists the different parallel system configuration options. Based on your choices, complete Checklist 10: Parallel system configuration (figure 6–4). Your Xerox service representative uses the checklist during installation. SYSTEM CONFIGURATION 6–9...
  • Page 76 This option allows you to select the code set and number of bits per character. EBCDIC and ISO encoding assume eight bits. XPPM assumes 8–bit encoding. In XPPM, ISO 6937 defaults to 8–bit ASCII. In HP IID mode, EBCDIC, and 7–bit ASCII are not supported. XEROX 4235 LPS INSTALLATION PLANNING GUIDE...
  • Page 77 This function is similar to the Vertical Format Units option on DataProducts printers. This is not supported in XPPM. Automatic printing enables the 4235 LPS to process documents without operator intervention. If automatic printing is disabled , the operator must release each job in the queue before it prints.
  • Page 78 Continuous , which traps the last 50K of transmitted or received data. The 4235 LPS can be accessible to you on three levels: Level 1 permits access only to the Print Mode screen. Level 2 permits access to Print Mode, Queue Management, Printer Setup, Document Formatting, and the Utilities screens.
  • Page 79 Time zone: Daylight savings: Note: To support VFU through the DataProducts interface, the Xerox service representative must set the appropriate dip switch on the SPC board so that data bit 8 appears on pin pair p–s. Data bit 8 on pin pair p–s:...

  • Page 80: Sna/Sdlc

    CCITT regulations V24/V28. Point–to–point operation is supported and may occur over switched or leased lines in half or full duplex mode. The connector used on the 4235 LPS is a 25–pin female "D" type. You must configure the 4235 LPS for EBCDIC character encoding when it is used with a host computer system that uses EBCDIC.

  • Page 81: Serial Cable

    Checklist 13: Serial system configuration–bisynchronous . The following SNA/SDLC and bisynchronous protocols are not supported: Direct host communication system–to–micro–diskette communication Card or ID reader Device–to–de vice data transfer (such as 4235 LPS to 4235 LPS) 4235 LPS–to–host computer system polling. SYSTEM CONFIGURATION User definable SDLC address 6–15...
  • Page 82 Source Description 4235 LPS Data transmitted to host computer system. Modem Data received from host computer system. 4235 LPS Asserted to allow the 4235 LPS to send. Modem Must be asserted to allow the 4235 LPS to transmit. Modem Must be asserted to allow the 4235 LPS to receive.

  • Page 83: Serial System Configuration Options-Sna/Sdlc

    This dialog allows you to enter an SDLC address and a 3–digit Terminal IDBLK followed by a three–digit terminal ID. The SDLC address is two digits. The 4235 LPS uses a three digit Terminal ID for 3777 mode. The 013=IDBLK and 000=terminal ID.
  • Page 84 You can enter an 8–character–maximum LOGMODE field used in logon statements. The 4235 LPS uses this field to construct a formatted logon statement when you select auto logon and formatted logon from Print mode.
  • Page 85 XPPM jobs is possible if you send an XPPM job to a port configured for XDPM with the data monitor enabled . When you select IBM, it remains active as long as the 4235 LPS does not receive the Xerox FCB Mode. In order to return to IBM mode, the host computer must send the IBM mode (3777 emulation) FCB.
  • Page 86 HP LaserJet IID XScript HP LaserJet IID Async Bisync XScript HP LaserJet IID XScript HP LaserJet IID Other:______ Other: ______ Other: _____(Default = 010000) ISO 6937 SDLC headers SNA headers Continuous Level 3 Mountain Central European XEROX 4235 LPS INSTALLATION PLANNING GUIDE...

  • Page 87: Serial System Configuration Options-Asynchronous

    7–bit ASCII EBCDIC ISO 6937 8–bit ASCII XEROX 4235 LPS INSTALLATION PLANNING GUIDE Table 6–6 lists the serial system configuration asynchronous options. If you choose to use an asynchronous serial interface, complete Checklist 12: Serial system configuration– asynchronous (figure 6–7). Your Xerox service representative uses the checklist during installation.
  • Page 88 4800 are used. When this protocol is in effect, the 4235 LPS sends an ACK (06H in ASCII, 2EH in EBCDIC) to the host computer system whenever an ETX (03H) is received to acknowledge the successful receipt of the preceding block of text.
  • Page 89 (negative, false) when the space in the input buffer is less than that of 64 characters. The line goes high (positive, true) when the 4235 LPS is ready to receive data. If this option is not in effect, the Data Terminal Ready line remains high at all times.
  • Page 90 Continuous , which traps the last 50K of transmitted or received data. You can assign access to the 4235 LPS users on three levels: Level 1 allows access only to the Print Mode screen. Level 2 allows access to Print Mode, Queue Management, Printer Setup, Document Formatting, and the Utilities screens.
  • Page 91 Job Timeout period: 10 seconds Other features Automatic printing: Line monitor trace window: User access: Date and time: MM/DD/YY Time zone: Daylight savings: XEROX 4235 LPS INSTALLATION PLANNING GUIDE Checklist 12: Serial system configuration–asynchronous Parallel SNA/SDLC XDPM XScript Enable Disable Enable Disable...

  • Page 92: Serial System Configuration Options-Bisynchronous

    Table 6–7 lists the serial system configuration bisynchronous options. If you choose to use a bisynchronous serial interface, complete Checklist 13: Serial system configuration– bisynchronous (figure 6–8). Your Xerox service representative uses the checklist during installation. Serial system configuration options–bisynchronous Description Select the 2nd interface .
  • Page 93 Odd or even parity must be chosen for 7–bit ASCII. Selecting no parity for 7–bit ASCII is invalid. These modes allow the 4235 LPS to react to commands and data streams as if it were one of these IBM RJE devices.
  • Page 94 Continuous , which traps the last 50K of transmitted or received data. You can assign access to the 4235 LPS users on three levels: Level 1 allows access only to the Print Mode screen. Level 2 allows access to Print Mode, Queue Management, Printer Setup, Document formatting, and the Utilities screens.
  • Page 95 Hold line period: Data monitor: Other features Automatic printing: Line monitor trace window: User access: Date and time: Time zone: Daylight savings: XEROX 4235 LPS INSTALLATION PLANNING GUIDE Checklist 13: Serial system configuration–bisynchronous Parallel SNA/SDLC XDPM XPPM Enable Disable Enable...
  • Page 96 SYSTEM CONFIGURATION 6–30 XEROX 4235 LPS INSTALLATION PLANNING GUIDE...

  • Page 97: Host Computer System Generation

    Host computer system generation This chapter provides guidelines for integrating and operating the 4235 LPS as a remote printer in a distributed remote job entry (RJE) network. This chapter also provides sample system generation parameters for five different environments, as well as operational hints.

  • Page 98: Os/Mvs Jes2

    2770, 2780, or 3780. As a remote terminal, OS/MVS and JES2 facilities support the 4235 LPS. The 4235 LPS is defined to a JES2 system using standard JES2 system generation statements and procedures. The five–step process requires only the addition of several generation statements to the JES2 initialization deck.
  • Page 99 LINE=xx TRANSP OPERATOR CLASS A= PRWIDTH=185 XEROX 4235 LPS INSTALLATION PLANNING GUIDE Step 2. Describe the 4235 LPS as a remote terminal with the RMTnn parameter. You must specify various parameters depending on the device. Mode Device 2770 RMTnn 2780...

  • Page 100: Sample Parameters

    OPERATOR CLASS A= TRANSP Sample parameters 7–4 Specifies the forms identifier to be loaded initially in the 4235 LPS. Step 4. Describe the 4235 LPS as a remote punch device with the Rnn.PUn parameter. The minimum specification is: Rnn.PU1 START,OPERATOR,CLASS=A where: Is the remote number, as defined in the RMTnn parameter.

  • Page 101: Sign-On Procedures

    2770 emulation mode only. As a remote terminal, OS/MVS and JES3 facilities support the 4235 LPS. The 4235 LPS is defined to a JES3 system using standard JES3 system generation statements and procedures. The four–step process requires only the addition of several generation statements to the JES3 initialization deck.
  • Page 102 Specifies a 2770–type printer. PR=1 Specifies a single printer. Specifies the optional keyboard/display. Specifies a line width of 255 characters for the 4235 LPS. You may also specify the following parameters for the RJPTERM statement: Indicates the 4235 LPS has an expanded buffer.

  • Page 103: Sample Parameters

    Switched line environment RJPLINE N=LINE7,A=030,F=DIAL RJPTERM N=RMT13,T=2770,PR=1,RD=1, F=XBUF,B=512, PRW=255 DEVICE DTYPE=RMT1403,JNAME=RMT13PR1, XLATE=NO,HEADER=NO DEVICE DTYPE=RMT2540, JNAME=RMT13PU1, XLATE=NO Sign–on is performed only from a 4235 LPS on a switched line. The format is: /*SIGNON RJPTERM name where: HOST COMPUTER SYSTEM GENERATION 7–7...

  • Page 104: Vm/Rscs

    7–8 Is in column 1 and RJPTERM starts in column 16. name Is the logical name of the 4235 LPS as specified in the RJPTERM statement. The 4235 LPS may be defined in a BSC environment as a remote job entry (RJE) terminal operating in any of the three modes available: 2770, 2780, or 3780.

  • Page 105: Sample Parameters

    Defines the virtual address of the switched line to be used. Step 3. Add the virtual and real UCB addresses for the installed 4235 LPS to the VM directory for RSCS by using the DEDICATE statement. Note: If other devices share the addresses, they may be already in the directory.

  • Page 106: Vse/Power

    TYPE=nnnn LIST=144 7–10 In an SNA environment, the 4235 LPS emulates a 3777 Model 3 communication terminal. The 4235 LPS may be defined in a BSC environment as a Remote Job Entry (RJE) terminal operating in any of the three modes available: 2770, 2780, or 3780. As a remote terminal, the 4235 LPS may be supported by standard VSE/POWER RJE facilities.

  • Page 107: Sample Parameters

    Specifies the transparency feature necessary for font downloading. No horizontal format control. Indicates multiple record feature. Step 3. Specify the line connecting each 4235 LPS to the host computer system with the LINE macro, as follows: PLINE ADDR=cnn(,SWITCH=xx),TIMEOUT=## where: Specifies the address of the line.

  • Page 108: Os/Vs1

    TPBFSIZ NPR=YES 7–12 In an SNA environment, the 4235 LPS emulates a 3777 Model 3 communication terminal. The 4235 LPS may be defined as a remote job entry (RJE) terminal operating in any of the three modes available: 2770, 2780, or 3780. As a remote terminal, OS/VS1 and JES/RES facilities support the 4235 LPS.
  • Page 109 = the number of the dedicated line for this terminal, if auto logon is used. Step 3. Specify the line connecting each 4235 LPS to the host computer system with the LINE macro, as follows: LINE LINEID=nn,LDESCR=(t,c) where: Is the line number.

  • Page 110: Sample Parameters

    Perform a standard RES and RTAM generation. Include the definitions of the RES data sets, SYS1.UADS, and SYS1. BROADCAST, and add logon procedures to PROCLIB. Step 5. Use the account facility to add user IDs for 4235 LPS users. Leased line environment LINE LINEID=1, . . .

  • Page 111: Sample Sna Parameters

    XEROX 4235 LPS INSTALLATION PLANNING GUIDE The definitions and parameters in the following section help the user install the 4235 LPS to emulate a 3777 in an SNA network. Most entries vary from one host computer system to another. Consult the network coordinator for this installation.

  • Page 112: Ncp Generation Sna Sample Definition

    NRZI=NO, PAUSE=.5, RETRIES=(8,5,7) Line definition for a switched line N01LN006 LINE ADDRESS=(006), CLOCKNG=EXT, DUPLEX=HALF, SPEED=4800, ANSWER=ON, CALL=IN, ISTATUS=ACTIVE PU definition for a switched line N01006P0 PUTYPE=2, MAXLU=8 LU definition for a switched line XEROX 4235 LPS INSTALLATION PLANNING GUIDE LNCTL=SDLC,...

  • Page 113: Vtam Switched Network Majornode Definition

    DIAL4235 N01DIAL2 DL370P00 DL370P01 DL370P02 XEROX 4235 LPS INSTALLATION PLANNING GUIDE Note: These are examples only. Make adjustments depending on your host and communication network. NCP, VTAM, and JES parameter settings for an RU size of 512 bytes. If running a multiple drop circuit, PASSLIM=1. For all non=multidrop leased lines, PASSLIM cannot be higher than 7 or data loss will occur.
  • Page 114 MODETAB BUF512 MODEENT, TSPROF='03' X PRIPROT=X'A3' SECPROT=X'A3' COMPROT=7080', RUSIZES=X'8686,* PSERVIC=X'01104000F100C80 00010040' NCP, VTAM, and JES parameter settings for an RU size of 512 bytes. XEROX 4235 LPS INSTALLATION PLANNING GUIDE TYPE=APPL AUTH=(ACQ,PASS), ACBNAME=NJEWC03, *MODETAB=MODENJE, * DLOGMOD=NJEMODE, VPACING=4** LOGMODE=NHEMODE LOGMODE=BUF512, FMPROF='03'...
  • Page 115 FCBs to your channel–attached 9700 LPS. Note: Perform one of the following for proper carriage control: 1. Set global JES2 parameter LINECT=0. 2. All output to the 4235 LPS must contain JCL card/*JOBPARM LINECT=0 following the JOB card. HOST COMPUTER SYSTEM GENERATION...
  • Page 116 Corresponds to VTAM to 4235 LPS LOGMODE=BUF512 Corresponds to IBM JES2 parmlib parameters for RMT Note: The sample 4235 LPS SDLC and SNA settings match the 3777 mode sample system generation parameters listed in the SNA sample definitions for a JES2 environment.

  • Page 117: Xerox Host Software Options

    Xerox Pen Plotter Interface (XPPI) Xerox Document Graphic Interface (XDGI) XEROX 4235 LPS INSTALLATION PLANNING GUIDE XPAF enables the 4235 LPS to support IBM data streams in the XPPM and XDPM environments. XPAF converts the data stream and resources from IBM Advanced Function Printing (AFP), to PDL/DJDE and XES jobs supported by 4235 LPS data stream.
  • Page 118 XDGI, DCF accepts standard SCRIPT/VS formatting control standard General Markup Language (GML) tags as input. DCF and GDDM interfaces are consistent with the existing user interface. You can easily access the features of the 4235 LPS without making significant changes to the existing jobs and applications.

  • Page 119: Fonts, Supplies, And Accessories

    The 4235 LPS requires paper, dry ink cartridges, print cartridges, fuser agent, and diskettes. It is important that these items are available when your 4235 LPS is installed. Plan on approximately five working days for delivery of your Xerox supplies.
  • Page 120 FONTS, SUPPLIES, AND ACCESSORIES Moisture content Paper storage 8–2 Sizes Table 8–1 lists the cut sheet paper sizes that the 4235 LPS accepts: Inches (A4) 8.27 x 11.69 8.5 x 11 8.5 x 13 8.5 x 14 (A3) 11.69 x 16.54 11 x 17 (A5) 5.83 x 8.27...

  • Page 121: Dry Ink, Print Cartridges, And Fuser Agent

    Accessories Paper cassettes XEROX 4235 LPS INSTALLATION PLANNING GUIDE Replace the dry ink cartridge when the 4235 LPS displays a message to do so. Replace the print cartridge when the 4235 LPS displays a message to do so or when there is a printing defect.
  • Page 122 FONTS, SUPPLIES, AND ACCESSORIES Micro diskettes 8–4 The 4235 LPS uses 3.5–inch double–sided, high–density micro diskettes. Each micro diskette is capable of storing approximately 1.44 MB of data. On installation day, you must provide the Xerox service representative with at least three 3.5–inch double–sided, high–...

  • Page 123: Supplies And Accessories List

    Supplies and accessories list Table 8–3. Item Paper Xerox paper qualities are 10 reams (5,000 sheets) per carton unless otherwise noted below. Unless noted otherwise, these papers are 20 lbs. in weight. 8.5'' x 11'' 8.5'' x 11'' 8.5'' x 11'' 8.5'' x 11''...
  • Page 124 3.5–inch, double–sided, high–density 1.44 MB diskette packaged 10 diskettes per box 1 liter bottle Note: Xerox transparencies are packaged 100 per box. All transparencies are 8.5 by 11 inches. Paper–backed transparencies are not supported. XEROX 4235 LPS INSTALLATION PLANNING GUIDE...
  • Page 125 (A4) (A4) (A4) (A4) (A4) XEROX 4235 LPS INSTALLATION PLANNING GUIDE Table 8–4 lists some of the supplies available from Rank Xerox. For a complete list, contact your Xerox sales representative. Table 8–4. Rank Xerox supplies list Description RX Nymolla–Black RX Nymolla DIN–4–hole punch,...
  • Page 126 30 to a view 33 to a view Packaged 1 per carton Packaged 1 cartridge per carton 3.5", double–sided, high–density 1.44 MB diskettes packaged 10 diskettes per box XEROX 4235 LPS INSTALLATION PLANNING GUIDE Part number 3R91030 3R96283 3R96281 3R96282 3R96169...

  • Page 127: How To Order Supplies

    822–2200. Contact your local Xerox sales representative for locations outside the United States. The Xerox supply order representative will ask you to supply the following information: The 4235 LPS serial number. (Your Xerox sales representative can provide you with this number.)
  • Page 128 Item Description Paper Labels Transparencies Paper cassettes 3.5–inch, high– double–sided, density micro diskettes Dry ink cartridge Print cartridge Fuser agent 8–10 Checklist 14: Supplies and accessories Quantity XEROX 4235 LPS INSTALLATION PLANNING GUIDE Date to Date order ordered...

  • Page 129: How To Order Fonts In The United States

    XEROX 4235 LPS INSTALLATION PLANNING GUIDE You can order licensed fonts from Xerox. If you plan to use a font that is not a 4235 LPS system font, place your order so that the font diskettes arrive before installation. You can order fonts on magnetic tape or diskette for downloading from your host computer system to the 4235 LPS hard disk.
  • Page 130 El Segundo, California 90245 The following list shows the approximate time it takes to receive your order. Call the Xerox Font Center for a more precise delivery schedule. Make sure you place your order in sufficient time to receive it before your scheduled installation.

  • Page 131: How To Order Fonts In Other Countries

    How to order fonts in other countries XEROX 4235 LPS INSTALLATION PLANNING GUIDE Xerox Font Technical Support In the United States, call the Xerox Font Technical Support Hotline at 1-800-445-FONT, option #1,to inquire about any technical font difficulties you may be experiencing. Business hours are 5:00 a.m.
  • Page 132 FONTS, SUPPLIES, AND ACCESSORIES 8–14 XEROX 4235 LPS INSTALLATION PLANNING GUIDE...
  • Page 133 Communication System. In SNA, the 4235 LPS can be defined as a RJE terminal operating in this mode. Software on the 4235 LPS that emulates an IBM 3777 Model 3 Communication Terminal. Software on the 4235 LPS that emulates an IBM 3780 Data Transmission Terminal.
  • Page 134 Control character that, unless set to be interpreted as a line end, causes the printer to begin printing at the left margin of the current line. Sometimes called a circuit, facility, or link. 1. In data communications, a path or line that enables two or more devices to communicate.
  • Page 135 In the 4235 printer, the dry ink cartridge and the print cartridge are CRUs. Feature of the 4235 LPS that prints the hexadecimal values of incoming codes and characters. The data monitor is used for troubleshooting.
  • Page 136 Control code or character represented by ASCII 27 (1BH), which must be placed in front of a printer command. The escape character (represented by the icon E) tells the printer to execute the following character string rather than print it.
  • Page 137 Method of duplex printing in which the bottom of the back page is printed in the same place as the top of the front page. Output tray on the 4235 LPS that is designed to hold and offset up to 2,000 sheets of 20 pound (80 gsm) paper.
  • Page 138 Message that you send from the host computer system to the 4235 LPS. The message may involve printer settings, special paper loading procedures, and other tasks. output 1. Material produced by a peripheral device of a computer, such as printout or magnetic tape.
  • Page 139 Used in XDPM. Allows the data to be printed by the 4235 LPS without interference from the 3777 emulation software. Unique word or set of characters that an operator or user must supply to log on to a system.
  • Page 140 (for example, storing text before sending it to a printer). One–page printout generated by a Xerox LPS containing information about the current interface used between the LPS and the host computer system, the encoding it uses, fonts in use, and errors within the current job that are detected by the system software.
  • Page 141 Routine record providing a list of chronological events (execution) of a program. translation table Feature on the 4235 LPS that maps one set of character codes to another. user–defined key. Substitute escape character defined by a user for specific print jobs.
  • Page 142 XES. Xerox Escape Sequences. Xerox printer command language. Asynchronous communication protocol for regulating data flow. XPPM Xerox Production Print Mode. 4235 LPS implementation of the Xerox Print Description Language. XScript 4235 LPS implementation of Adobe PostScript. XEROX 4235 LPS INSTALLATION PLANNING GUIDE...
  • Page 143 Supplies and accessories, 8-10f communication requirements, 3-6 components, 1-4f computer system generation, host, 7-1 to 7-22 configurations 4235 LPS minimum and maximum, 1-5 parallel, 6-9 to 6-13 serial asynchronous, 6-21 to 6-25 serial bisynchronous, 6-26 to 6-29 serial SNA/SDLC, 6-17 to 6-20...
  • Page 144 1-10 printer setup options, 4-9 to 4-11 humidity range, 3-2 IBM sample PARMLIB parameters JES2, 7-19 JES3, 7-20 identifying 4235 LPS to host computer system, 2-7 image generator board, 1-6 initialization process review OS/MVS JES2, 7-2 OS/MVS JES3, 7-5...
  • Page 145 8-9 OS/MVS JES2, 7-2 to 7-4 OS/MVS JES3, 7-5 to 7-7 OS/VS1, 7-12 to 7-14 paper, 8-1 to 8-2 XEROX 4235 INSTALLATION PLANNING GUIDE parallel cable, 6-2 interface information, 6-2 to 6-13 system configuration options, 6-9 to 6-13...
  • Page 146 6-16 system configuration asynchronous, 6-21 to 6-25 bisynchronous, 6-26 to 6-30 SNA/SDLC, 6-17 to 6-20 settings 4235 LPS user interface, 7-20 Auto Log-on and Formatted Log-on, 7-20 SDLC, 6-21 user interface, 7-20 signal timing Centronics, 6-5f Data Products, 6-8f...
  • Page 147 = figure; t = table VM/RSCS, 7-8 to 7-9 WARNING, xii weight and dimensions, 3-2 XDGI, see Xerox Document Graphics Interface XDPM document formatting options, 5-1 to 5-4 fonts, 1-7 printer setup options, 4-1 to 4-3 Xerox Distributed Print Mode, see XDPM...
  • Page 148 INDEX f = figure; t = table INDEX-6 XEROX 4235 INSTALLATION PLANNING GUIDE...

Table of Contents