Advertisement
Available languages
Available languages
Quick Links
Washout Port Kit
Model No. 112-5803
Removing the Bolt from the
Mower Housing
No Parts Required
Procedure
1. Shut off the engine and wait for all moving
parts to stop.
2. Disconnect the wire from the spark plug.
If you leave the wire on the spark plug,
someone could accidently start the
engine and injure you or bystanders.
Disconnect the wire from the spark plug
before you perform any maintenance.
Also, move the wire away so that it does
not accidentally contact the spark plug.
3. Clean the underside of the mower housing and
examine it for damage or excessive wear.
A corroded or cracked mower housing
may be further weakened by installing
the washout port, causing the mower
housing to crack and break, exposing
you or others to thrown objects and to
the running blade.
• Install the washout port only on a
sound mower housing.
• Replace a worn, cracked, or damaged
mower housing immediately.
• Never put your hands or feet under or
through the openings in the mower
housing.
4. Remove the large bolt and nut from the mower
housing.
© 2006—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
Installing the Washout Port
Parts needed for this step:
1
Washout port
2
Bolt
2
Washer
2
Locknut
Procedure
1. Secure the washout port to a garden hose.
2. Insert the washout port (attached to the garden
hose) into the hole in mower housing where
you removed the large bolt and move the
washing port and garden hose to the preferred
location.
Note: The hose should not interfere with the
wheels, handles, or controls.
3. Use the washout port as a template to mark
the location of the two holes in the mower
housing for the fasteners.
4. Center punch and drill the two holes (9/32-inch
diameter) that you marked in step 3.
5. Install the washout port on the mower facing
outward, and secure it with the bolts and
locknuts provided in the kit (Figure 1).
1
1. Bolt (2)
2. Washer (2)
3. Washout port
Register at www.Toro.com.
Form No. 3355-330 Rev A
Installation Instructions
2
3
4
5
Figure 1
4. Garden hose
5. Locknut (2)
Original Instructions (EN)
Printed in the USA.
All Rights Reserved
G003843
Advertisement
Related Manuals for Toro 112-5803
Summary of Contents for Toro 112-5803
- Page 1 Form No. 3355-330 Rev A Washout Port Kit Model No. 112-5803 Installation Instructions Removing the Bolt from the Installing the Washout Port Mower Housing Parts needed for this step: No Parts Required Washout port Bolt Washer Procedure Locknut 1. Shut off the engine and wait for all moving parts to stop.
- Page 2 Washing the Underside of the Mower Wash the underside of the mower housing after each use to prevent buildup of grass clippings for improved mulching and clipping dispersal. 1. Park the mower on a hard level surface. 2. Disengage the power takeoff (PTO). 3.
- Page 3 Form No. 3355-330 Rev A Kit raccord de lavage N° de modèle 112-5803 Instructions d'installation Retrait du boulon du carter de la tondeuse Si le carter de la tondeuse est corrodé ou fissuré, il pourra être encore affaibli par Aucune pièce requise la pose du raccord de lavage.
- Page 4 Lavage du carter de 4. Marquez au pointeau et percez les deux trous tondeuse (9/32 pouce de diamètre) repérés à l'étape 3. 5. Montez le raccord de lavage sur le plateau de Lavez le dessous du carter de la tondeuse après coupe, en le dirigeant vers l'extérieur, et fixez-le chaque utilisation pour éviter l'accumulation avec les boulons et contre-écrous fournis dans...