Table of Contents
Advertisement
Quick Links
Slope Sensor Kit
Model No. 02945
Model No. 02946
Model No. 02947
Model No. 02949
Model No. 02950
Refer to the following table for the appropriate
kit, traction unit, and traction-unit serial number
combination:
Kit Model
Traction Unit Model
Number
Number
02750 (T4240)
30654 (CT2240)
02945
31654 (CT2240)
30657 (LT3340—cab
equipped)
30657 (LT3340)
02946
30659 (LT-F3000)
30659
02947
(LT-F3000—cab
equipped)
02750 (T4240—cab
02949
equipped)
02950
31050TE (PLH800)
© 2020—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
Serial Number
405398421 and above
405623665 and above
All serial numbers
405006390 and above
405006390 and above
404879018 and above
404879018 and above
405398421 and above
320000155 and above
Register at www.Toro.com.
Safety
Safety and Instructional
Decals
Safety decals and instructions are
easily visible to the operator and are
located near any area of potential
danger. Replace any decal that is
damaged or missing.
1. 1. Warning—read the Operator's Manual; a fast flashing
light and alarm sounding indicates a steep slope; a slow
flashing light indicates a moderate slope; no light indicates
normal operating conditions.
Original Instructions (EN)
All Rights Reserved *3437-895* A
Printed in the USA
Form No. 3437-895 Rev A
Installation Instructions
140-2710
decal140-2710
Advertisement
Table of Contents
Related Manuals for Toro 02945
Summary of Contents for Toro 02945
- Page 1 Form No. 3437-895 Rev A Slope Sensor Kit Model No. 02945 Model No. 02946 Model No. 02947 Model No. 02949 Model No. 02950 Installation Instructions Safety Refer to the following table for the appropriate kit, traction unit, and traction-unit serial number...
-
Page 2: Installation
Installation Preparing the Machine No Parts Required Procedure Park the machine on a level surface. Engage the parking brake. Lower the cutting unit(s). g304899 Shut off the machine and remove the key. Figure 1 1. Slope sensor mount 3. Slope sensor 2. - Page 3 g307377 g305020 Figure 5 Figure 3 1. LED light 1. Bolt (M10) 3. Flange nut (M10) 2. Slope sensor mount Connect the remaining wire-harness connectors as follows: Install the wire harness connector labeled P02 • Wire harness connector labeled P01: to the slope sensor (Figure Connect to one of the 6-pin sealed...
- Page 4 Connect the LED light to the wire-harness connector labeled P08 (Figure g308240 Figure 6 1. Slope-sensor decal g304404 Figure 8 Installing the Kit 1. Wire harness 5. Connector—P09 2. Connector—P08 6. Control pod CT2240, LT3340, and LTF Machines 3. LED light 7.
- Page 5 Install the slope-sensor decal adjacent to the machine-stability decal on the storage-pod lid (Figure 11). g304544 Figure 9 1. Bolt (M6 x 35 mm) 3. Slope sensor 2. Slope sensor mount 4. Flange nut (M6) g308336 Figure 11 Connect the wire-harness connector labeled 1.
- Page 6 Remove the steering wheel, dashboard, and front panel (Figure 13). Note: Carefully lift off the dashboard, ensuring that the connectors to the existing switches are not disturbed. g307287 Figure 14 1. LED light 2. Slope sensor decal g307374 Figure 13 1.
- Page 7 g307376 Figure 18 g307375 Figure 16 1. Wire-harness-routing direction 1. Alarm Connect the remaining wire-harness connectors as follows: • Wire harness connector labeled P08: Connect to the LED light. • Wire harness connector labeled P09: Connect to the alarm. Use a cable tie to coil together any additional amount of wire harness in front of the battery (Figure 19).
-
Page 8: Calibrating The Sensor
Calibrating the Sensor No Parts Required Procedure While the machine is on a flat surface, remove the plug from calibration connectors (labeled P05 and P06). Plug the connectors together. Turn the ignition key to the O position, but do not start the engine. Note: The LED light blinks as the sensor calibrates.