Copyright 2014 by JVC KENWOOD Corporation. All While every precaution has been taken in the preparation rights reserved. of this manual, JVC KENWOOD Corporation assumes no No part of this manual may be reproduced, translated, responsibility for errors or omissions. Neither is any liability...
TK-3501 REALIGNMENT 1. Modes Note: User mode • The data stored in the personal computer must match Model Name and Model Type when it is written into EE- PROM. PC mode Data programming mode • Do not press the [PTT] key during data transmission or reception.
TK-3501 REALIGNMENT KPG-22A or KPG-22U Gray – Gray/Black 1.5D-XV Lead wire – 1.5D-XV Shield wire Tuning cable (E30-3216-05) D-SUB (9-pin) KPG-22A KPG-22U Transceiver Transceiver Fig. 1 DISASSEMBLY FOR REPAIR 1. Separating the Case Assembly from the 4. Taking care not to cut the speaker lead ( d ), open the chassis and case assembly.
Page 5
TK-3501 DISASSEMBLY FOR REPAIR 2. Removing the TX-RX unit from the 4. Removing the Antenna element Chassis When you remove an antenna element, do not give a damage to an antenna element as shown in the figure. 1. Remove the packing ( e ).
TK-3501 CIRCUIT DESCRIPTION 1. Frequency Configuration The receiver utilizes double conversion. The first IF is 38.85MHz and the second IF is 450kHz. The first Local os- cillator is supplied from the PLL circuit. The PLL circuit in the transmitter generates the neces- sary frequencies.
Page 7
TK-3501 CIRCUIT DESCRIPTION 3. Transmitter System 2-3. IF Amplifier Circuit The first IF signal is passed through a four-pole mono- 3-1. Microphone Amplifier Circuit lithic crystal filter (XF200) to remove the adjacent channel The signal from microphone amplified by IC301 and goes signal.
Page 8
TK-3501 CIRCUIT DESCRIPTION 4. Frequency Synthesizer Circuit Note: The EEPROM stores tuning data (Deviation, Squelch, 4-1. Frequency Synthesizer etc.). The frequency synthesizer consists of the TCXO (X1), Realign the transceiver after replacing the EEPROM. VCO, PLL IC (IC1) and buffer amplifiers.
TK-3501 SEMICONDUCTOR DATA MCU: F2136ACNFKFMA (TX-RX unit: IC400) Pin No. Signal Name Function Pin No. Signal Name Function VOXINLEVEL VOX level input VREF Reference voltage input CV_DET VCO voltage detection MODE Mode select for MCU LSDO Low speed data output...
TK-3501 COMPONENTS DESCRIPTION TX-RX unit (X57-8992-70) Ref. No. Part Name Description Q603 Transistor DC switch Ref. No. Part Name Description Q604 Transistor DC switch PLL system Diode Current steering IC200 FM IF system IC300 Variable capaci- Frequency control/ VCO tance diode...
Page 12
CK73HB1C103K CHIP C 0.010UF C101 CC73HCH1H271J CHIP C 270PF C225 CC73HCH1H060B CHIP C 6.0PF C102 CC73HCH1H220J CHIP C 22PF C226 CK73HBB1H471K CHIP C 470PF C103 CC73GCH1H221J CHIP C 220PF C227 CK73HB1C103K CHIP C 0.010UF E: TK-3501 E T: TK-3501 T...
Page 13
CC73HCH1H271J CHIP C 270PF C329 CK73HBB1C333K CHIP C 0.033UF C523 CC73HCH1H271J CHIP C 270PF C330 CK73HBB1H102K CHIP C 1000PF C524 CC73HCH1H271J CHIP C 270PF C332 CK73HB1C103K CHIP C 0.010UF C525 CC73HCH1H271J CHIP C 270PF E: TK-3501 E T: TK-3501 T...
Page 14
CHIP R 1/16W R323 RK73HB1J562J CHIP R 5.6K 1/16W R324 RK73HH1J473D CHIP R 1/16W R119 RK73GB2A391J CHIP R 1/10W R325 RK73HH1J473D CHIP R 1/16W R120 RK73HB1J331J CHIP R 1/16W R327 RK73HB1J824J CHIP R 820K 1/16W E: TK-3501 E T: TK-3501 T...
Page 15
FUSE(1.6A) R505 RK73HB1J473J CHIP R 1/16W R508 RK73HB1J473J CHIP R 1/16W CF200 L72-1046-05 CERAMIC FILTER(450KHZ) If a part reference number is listed in a shaded box, that part does not come with the PCB. E: TK-3501 E T: TK-3501 T...
Page 16
S402 S6A-0002-00 ROTARY SWITCH(SELECTOR) TH100 B57331V2104J THERMISTOR (100K) TH260 B57331V2104J THERMISTOR (100K) J30-1308-04 SPACER (MIC) If a part reference number is listed in a shaded box, that part does not come with the PCB. E: TK-3501 E T: TK-3501 T...
TK-3501 EXPLODED VIEW 11x4 S400 Bx13 J301 J300 MIC300 VR500 CF200 S402 CD200 TX-RX unit A : N30-2606-48 B : N83-2005-48 Parts with the exploded numbers larger than 700 are not supplied. If a part reference number is listed in a box on the exploded view of the PCB, that part does not come with the PCB.
TK-3501 ADJUSTMENT Test Equipment Required for Alignment Test Equipment Major Specifications Frequency Range 400 to 520MHz Standard Signal Generator (SSG) Modulation Frequency modulation and external modulation Output –127dBm/0.1µV to greater than –47dBm/1mV Input Impedance 50Ω RF Power Meter Operation Frequency...
Page 19
TK-3501 ADJUSTMENT Frequency and Signaling Preparations for Tuning the Transceiver The transceiver has been adjusted for the frequencies Before attempting to tune the transceiver, connect the shown in the following table. When required, re-adjust them unit to a suitable power supply.
Page 20
TK-3501 ADJUSTMENT Common Section Measurement Adjustment Item Condition Specifications / Remarks Test- Unit Terminal Unit Parts Method equipment 1. Setting 1) BATT terminal voltage: 7.5V 2) SSG standard modulation [Narrow] MOD: 1kHz, DEV: 1.5kHz 2. VCO Lock 1) Adj item: High TX-RX ANT 2.2V...
Page 21
TK-3501 ADJUSTMENT Measurement Adjustment Item Condition Specifications / Remarks Test- Unit Terminal Unit Parts Method equipment 7. Battery 1) BATT terminal voltage: 5.7V Power TX-RX ANT Check LED blinks Detection PTT: ON meter No transmit power Check (User mode) BATT 2) BATT terminal voltage: 7.5V...
Spurious Emission ..........–36dBm (30MHz~1GHz) –30dBm (1GHz~4GHz) Modulation Distortion ..........Less than 5% FM Noise ...............40dB Modulation .............8K50F3E Measurements made per EN standards or TIA/EIA 603 and specifications shown are typical. JVC KENWOOD Corporation reserves the right to change specifications without prior notice or obligation.