2. When the cover is open, close viewing through the objective lens with the naked eye will cause exposure to the laser beam. ∗ : See page 16. /C LO M EN M EN DV-300-S...
Page 3
To protect products from damages or failures during transit, the shipping mode should be set or the shipping screws should be installed before shipment. Please be sure to follow this method especially if it is specified in this manual. DV-300-S...
• Soldering time: Within 3 seconds • Soldering combination: Sn-3.0Ag-0.5Cu • When Soldering/Removing of solder, use the draw in equipment over the Pick Up Unit to prevent the Flux smoke from it. Short circuit using a soldering iron. Pick Up PCB Fig. 1 DV-300-S...
• Place the unit on a workstation equipped to protect against static electricity, such as conductive mat. • Soldering iron with ground wire or ceramic type is used. • A worker needs to use a ground conductive wrist strap for body. DV-300-S...
DECK DOES NOT ACCEPT OPEN/CLOSE Is the voltage at Check P.CON 6V line of pin 8 and 19 of IC2301 POWER BLOCK. about DC6V ? Check CD2302 Is the lose connection connection to DECK. at CD2302 to DECK ? Change DVD LOADER. DV-300-S...
Page 12
Replace V651 or IC651. NO PLAYBACK PICTURE OF AV JACK Is there Check IC4001 and a signal at pin 164 of peripheral circuit. IC4001 ? Is there Check J7302 and peripheral video signal at pin 33 circuit. of IC7301 ? Change IC7301. DV-300-S...
Page 13
NO ANALOG AUDIO ON PLAYBACK Is there Check J8003 and peripheral AUDIO signal at pins 1 and 7 circuit. of IC8003 ? Is there Check AT pins 184 and AUDIO signal at C8051 186 of IC4001. and C8053 ? Change IC8003. DV-300-S...
Page 14
Any kind of symptoms (no power, a failure in any of the servo, video and audio systems, etc.) may be (DVD MT PCB Assy : IC4001) generated, because the DVD processing is performed by a single chip. 64M SDRAM No power. (DVD MT PCB Assy : IC4005) Block noise is generated during playback. DV-300-S...
No playback of a CD : Measure the voltage between the two ends of R2320 or R2322 on the DVDM Assy. If the voltage is 0.4 V or higher, the 780-nm LD is degraded. DVD MT PCB ASSY Front side SIDE A DV-300-S...
• After going into test mode, if you play back the disc, "DISC-NON" is displayed. • The video signal and the audio signal are outputted during the test mode. • The SKIP key and the SCAN key are effective during the test mode. TEST MODE: OFF POWER GGF1381 Test mode remote control unit DV-300-S...
3 LD ON DVD : Press the [TEST] (A8-5E) and [1] (A8-01) keys in order, and turn on the laser diode (650n). : Press the [TEST] (A8-5E) and [4] (A8-04) keys in order, and turn on the laser diode (780n). DV-300-S...
: [NTSC] PAL system : [PAL] Automatic setting : [AUTO] Scart terminal output [SK – ∗ ∗] (Display only the WY model which can do the output setting of scart terminal.) VIDEO : [00] S-VIDEO : [01] : [02] DV-300-S...
• Region confirmation mode (ESC + A.MON [Test mode remote control unit] + "1"-"8" [Test mode remote control unit] keys) After you press the A.MON key while holding the ESC key pressed and then input the region number, if the number is different from that set in the unit, an error message is displayed, and the tray opens. DV-300-S...
%%e -2 : NG 7.0e -4 : NG 3 EDC/ID error history (ID Address, EDC/ID errors, last eight errors) Note: ∗ Error of AV1 is not supported in this player. Indication plan contents Character in bold : Item name : Information display DV-300-S...
Up PCB and DVD MT PCB connector. 1-4: DVD MT PCB (Refer to Fig. 1-4) 1. Remove the 3 screws 1. 2. Remove the 4 screws 2. 3. Remove the DVD MT PCB in the direction of arrow. Fig. 1-2 DVD MT PCB Fig. 1-4 DV-300-S...
Page 23
3 supports 1. between A and B. Fig. 2-3-D 2. Remove the Plate Clamper, Magnet Clamper and Clamper. Check Hook Check Hook Plate Clamper Magnet Clamper Main Frame Loading Motor PCB Ass’y Check Hook Clamper Fig. 2-3-E Fig. 2-5-A DV-300-S...
Page 24
6. Remove the Switch PCB Ass'y. 7. Remove the screw 4. Feed Motor 8. Remove the Gear Feed. 9. Remove the 2 screws 5. 10. Remove the Feed Motor. Safety surface for pressing 11. Remove the Gear Motor. of the insert. Fig. 2-7-C DV-300-S...
Page 25
Fig. 2-8. NOTE 1. Do not make the folding lines except the specified positions for the FFC. [ 24 pin FFC ] Fold Printing Surface 79 ± 1 mm Reinforcement Plate To Pick Up PCB Fig. 2-8 DV-300-S...
While the screen shown at left is being displayed, updating is in progress. DO NOT TURN OFF THE POWER DURING UPDATING. 4 Updating of the firmware is completed. When the screen with the Pioneer logo is displayed, updating is completed. The time required for updating is about 5 minutes. DV-300-S...
2 If updating of the firmware using the disc for updating failed • Was the disc for updating recognized properly? Check if the volume label of the disc is PIONEER. • Is playback of a disc other than the disc for updating possible? If playback of a test CD is also impossible, a reading section, such as PU, may be defective.
For the applying amount of lubricants or glue, follow the instructions in this manual. (In the case of no amount instructions, apply as you think it appropriate.) 6.1 PACKING SECTION WYXZT/UR5 Only WYXZT/UR5 Only WYXZT/UR5 Only WYXZT/UR5 Only DV-300-S...
Page 29
See Contrast table (2) Operating Instructions (S/D) See Contrast table (2) Operating Instructions (R) See Contrast table (2) (2) CONTRAST TABLE DV-300-S/WYXZT5, /WYXZT/UR5, DV-300-K/WYXZT5 and WYXZT/UR5 types are constructed the same except for the following : DV-300-S/ DV-300-S/ DV-300-K/ DV-300-K/ Mark No.
6.2 EXTERIOR SECTION NON-CONTACT SIDE CONTACT SIDE DV-300-S...
Page 31
8965TS101B Cord Jumper (CD7301) 122H0C3002 • • • • • • Screw,Tap Tite(S)-Bind Wash. 816423063U (2) CONTRAST TABLE DV-300-S/WYXZT5, /WYXZT/UR5, DV-300-K/WYXZT5 and /WYXZT/UR5 types are constructed the same except for the following : DV-300-S/ DV-3003-S/ DV-300-K/ DV-300-K/ Mark No. Symbol and Description...
Note : (SW PCB ASS'Y) CD2301 NOTE: Applying positions AA, AB and AC for the CLASS PART NO. MARK grease are displayed for this section. GREASE GEM1018 Check if the correct grease is applied for each GYA1001 position. GEM1036 DV-300-S...
DVD-R/RW compatibility • Compatible formats: DVD-Video, Video Recording (VR)* * Edit points may not play exactly as edited; Super VCD screen may go momentarily blank at edited points. • Unfinalized playback: No • WMA/MP3/JPEG file playback on DVD-R/ RW: No DV-300-S...
Page 35
In these particular instances, check with the software publisher for more detailed information. Discs recorded in packet write mode (UDF format) are not compatible with this player. Check the DVD-R/RW or CD-R/RW software disc boxes for additional compatibility information. DV-300-S...
Returns to the previously dis-played menu screen. • Press to jump to the previous/next 7 HOME MENU chapter or track. 8 Display Compatible Description of the display. This mark indicates compatibility with DVD-RW discs recorded on a DVD recorder in Video Recording mode. DV-300-S...
Press to pause playback; press again to restart. 12 PLAY MODE Press to display the Play Mode menu. (You can also get to the Play Mode menu by pressing HOME MENU and selecting Play Mode). Press to jump to the beginning of the current DV-300-S...
Page 39
Use to select menu options, etc. playing. 24 ZOOM 18 MENU Press to change the zoom level. Press to display a DVD disc menu, or the Disc Navigator if a VR format DVD-RW, CD, Video CD , MP3, WMA or JPEG disc is loaded. DV-300-S...
-28V DPF010 ATTENTION CAUTION :LES PIECES REPAREES PAR UN ETANT :SINCE THESE PARTS MARKED BY DANGEREUSES AN POINT DE VUE SECURITE CRITICAL FOR SAFETY,USE ONES N’UTILISER QUE CELLS DECRITES DESCRIBED IN PARTS LIST ONLY DANS LA NOMENCLATURE DES PIECES DV-300-S...
Page 41
LIMIT SW SW(GND) SW(GND) FG SENSER CP2302 DVD PCB PCB130 CLOSE CLOSE DMF089 GND(D) GND(D) OPEN OPEN DVD MECHA ASSY (A2K001A650) NOTE: THIS INTERCONNECTION DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE DV-300-S...
55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 DQ11 DQ12 DQ13 DQ14 DQ15 DBA0 DBA1 MA10 MA11 SDCKE SDCLK 1.8V NOTE:THE DC VOLTAGE EACH PART WAS MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK. DV-300-S...
Page 43
TP4035 TP4092 R4075 R4039 10K RESET TP4093 TP4094 RESET C4118 (V+3D) 100P CH NR4001 4D03WGJ0330T5E B4011 PCB130 MMZ1608R102CT R4076 DMF089 NOTE: T HIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE DV-300-S...
0.001 B DQM0 C4040 DCAS# DRAS# DBA1 DBA0 NC (WP#/ACC) SDCLK DCS# RY/BY# PRD# PCE# PRD# PCE# PWR# FROM/TO POWER PORT (V+3D) D_GND NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE DV-300-S...
Page 45
DQM0 NC/RFU LDQM DQM1 DWE# UDQM SDCLK DCAS# CAS# SDCKE DRAS# RAS# DCS# MA11 DBA0 BA0/A13 DBA1 BA1/A12 MA10 A10/AP C4055 0.1 B TP4001 NOTE:THE DC VOLTAGE EACH PART WAS PCB130 MEASURED WITH THE DIGITAL TESTER DMF089 DURING PLAYBACK. DV-300-S...
LIMIT SW 3.3K TP2333 TP2325 MOT_SLED- SLD- TP2326 Sled MOT_SLED+ SLD+ R2329 R2310 TP2327 SPD- TP2328 MOT_SPDL+ SPD+ MOT_SPDL- C2307 V+3F 0.1 B W802 C2311 0.1 B NOTE:THE DC VOLTAGE EACH PART WAS MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK. DV-300-S...
Page 47
0.1 B OPIN VOTR- Vcc2 VOTR+ W806 VOLD- VOSL+ C2312 W805 0.1 B VOLD+ VOSL- VOTK- VOFC- VOTK+ VOFC+ NOTE: T HIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME PCB130 OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE DMF089 DV-300-S...
NA_P R8048 FROM/TO VIDEO JACK 470K AUDIO_L AUDIO_R V+5V_A NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME NOTE:THE DC VOLTAGE EACH PART WAS OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK. DV-300-S...
: VIDEO SIGNAL ROUTE (B/CB ch) : AUDIO SIGNAL ROUTE (L ch) D_GND NOTE:THE DC VOLTAGE EACH PART WAS NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME MEASURED WITH THE DIGITAL TESTER OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE DURING PLAYBACK. DV-300-S...
Page 51
AUDIO R CVBS OUT IC7302 4CH BUS SW SN74CBT3257PWR (GY) (B/CB) (R/CR) (R/CR) YUV only ---> W871,W872,W873,R7306 ON YUV/D ---> W871,W872,W873,W874,W875,W876,R7306 ON RGB/YUV ---> IC7302 MOUNT,JP DEL,R7305 ON J7302 RCA-405A-08 CVBS/Y/U/V CAUTION: DIGITAL TRANSISTOR CAUTION: DIGITAL TRANSISTOR PCB130 DMF089 DV-300-S...
FL DC+ -28V ATTENTION CAUTION :LES PIECES REPAREES PAR UN ETANT :SINCE THESE PARTS MARKED BY DANGEREUSES AN POINT DE VUE SECURITE CRITICAL FOR SAFETY,USE ONES N’UTILISER QUE CELLS DECRITES DESCRIBED IN PARTS LIST ONLY DANS LA NOMENCLATURE DES PIECES DV-300-S...
Page 53
FLDC- FLDC+ -28V D_GND TO MEMORY D_GND NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME NOTE:THE DC VOLTAGE EACH PART WAS OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK. PCB130 DMF089 DV-300-S...
EJECT SW666 EVQ11L05R PCB280 DEF129 Vout OS651 ROM-V340TAO NOTE:THE DC VOLTAGE EACH PART WAS NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME MEASURED WITH THE DIGITAL TESTER OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE DURING PLAYBACK. DV-300-S...
Page 55
FP_DI DI (M to F) 100P CH FP_DO DO (F to M) FFC(1.0mm pitch) V+3E R666 V+3E V+3E CD601 C604 2H0B1003 2.2 1/4W DGND C605 33P CH DGND TP663 0.001 B FLDC+ FLDC+ -28V -28V FLDC- FLDC- PCB270 DEF126 DV-300-S...
EVQ11L05R EJECT SW666 EVQ11L05R PCB280 DEF129 Vout OS651 ROM-V340TAO NOTE:THE DC VOLTAGE EACH PART WAS NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME MEASURED WITH THE DIGITAL TESTER OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE DURING PLAYBACK. DV-300-S...
Page 57
00_6232_011_102_800+ FP_SCK FFC(1.0mm pitch) FP_DI DI (M to F) CD601 FP_DO 2H0B1003 DO (F to M) V+3E R666 V+3E V+3E C604 2.2 1/4W DGND C605 33P CH DGND TP663 0.001 B FLDC+ FLDC+ -28V -28V FLDC- FLDC- PCB270 DEF126 DV-300-S...
:SINCE THESE PARTS MARKED BY REPLACE ONLY WITH THE SAME TYPE FUSE CRITICAL FOR SAFETY,USE ONES 1.6A 125V{F501} DESCRIBED IN PARTS LIST ONLY ATTENTION :POUR UNE PROTECTION CONTINUE LES RISQUES D’INCEIE N’UTILISER QUE DES FUSIBLE DE MEME TYPE 1.6A 125V{F501} DV-300-S...
Page 59
NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME NOTE:THE DC VOLTAGE EACH PART WAS DANGEREUSES AN POINT DE VUE SECURITE OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE MEASURED WITH THE DIGITAL TESTER N’UTILISER QUE CELLS DECRITES DURING PLAYBACK. DANS LA NOMENCLATURE DES PIECES DV-300-S...
Page 61
On that occasion, replace whole Assy. NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME NOTE:THE DC VOLTAGE EACH PART WAS PCB240 OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE MEASURED WITH THE DIGITAL TESTER DPF015 DURING PLAYBACK. DV-300-S...
Symbol In PCB Symbol In Schematic Part Name Diagrams Diagrams C E B Capacitor Connector Transistor B C E SIDE A Transistor with resistor B C E Field effect SIDE B P.C.Board Chip Part transistor Resistor array 3-terminal regulator DV-300-S...
Page 73
TV Encoder Module Videop RF Amplifier Video DAC Servo IO Servo Motor Processor Video Drive Processor interlacer Spindle Control FLASH MPEG-1/2 Audio JPEG Memory Video Decoder Controller DRAM System Audio Parser Audio Output CPPM/CPRM SPDIF System GPIO 32-bit RISC IR/VFD DV-300-S...
Page 83
Note: 1. The Main column is the main function, Alt. means alternative function. 2. The external TV encoder mode only supports CCIR-656 mode. DV-300-S...