hit counter code
Lenovo IDEACENTRE 300s series Maintenance Manual
  1. Manuals
  2. Brands
  3. Lenovo Manuals
  4. All-in-one pcs
  5. IDEACENTRE 300s series
  6. Maintenance manual

Lenovo IDEACENTRE 300s series Maintenance Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

ideacentre 300S Series Hardware Maintenance
Manual
Machine Types: 90DQ [300S-11IBR/Energy Star] and 90D9
[300S-11ISH/Energy Star]

Advertisement

Table of Contents
loading

Summary of Contents for Lenovo IDEACENTRE 300s series

  • Page 1 300S Series Hardware Maintenance Manual Machine Types: 90DQ [300S-11IBR/Energy Star] and 90D9 [300S-11ISH/Energy Star]...
  • Page 3 300S Series Hardware Maintenance Manual Machine Types: 90DQ [300S-11IBR/Energy Star] and 90D9 [300S-11ISH/Energy Star]...
  • Page 4 First Edition (October 2015)30th © Copyright Lenovo 2015. LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software are delivered pursuant a General Services Administration “GSA” contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No. GS-35F-05925...

  • Page 5: Table Of Contents

    Selecting a startup device ..Replacing the motherboard..Exiting the Lenovo BIOS Setup Utility program . . FRU lists-H30–05 ... . .
  • Page 6 300S Series Hardware Maintenance Manual...

  • Page 7: Chapter 1. About This Manual

    This manual contains service and reference information for ideacentre 300S serious computers listed on the cover. It is intended only for trained servicers who are familiar with Lenovo computer products. Before servicing a Lenovo product, be sure to read the Safety Information.
  • Page 8 300S Series Hardware Maintenance Manual...

  • Page 9: Chapter 2. Safety Information

    Electrical current from power, telephone, and communication cables can be hazardous. To avoid personal injury or equipment damage, disconnect the attached power cords, telecommunication systems, networks, and modems before you open the computer covers, unless instructed otherwise in the installation and configuration procedures. © Copyright Lenovo 2015...
  • Page 10 – Blowers and fans – Motor generators and similar units. (This practice ensures correct grounding of the units.) • If an electrical accident occurs: – Use caution; do not become a victim yourself. – Switch off power. ideacentre 300S Series Hardware Maintenance Manual...

  • Page 11: Safety Inspection Guide

    – Send another person to get medical aid. Safety inspection guide The intent of this inspection guide is to assist you in identifying potentially unsafe conditions on these products. Each machine, as it was designed and built, had required safety items installed to protect users and service personnel from injury.

  • Page 12: Grounding Requirements

    • Connect and disconnect cables as described in the following table when installing, moving, or opening covers on this product or attached devices. ideacentre 300S Series Hardware Maintenance Manual...
  • Page 13 To Connect To Disconnect 1. Turn everything OFF. 1. Turn everything OFF. 2. First, attach all cables to devices. 2. First, remove power cords from outlet. 3. Attach signal cables to connectors. 3. Remove signal cables from connectors. 4. Attach power cords to outlet. 4.
  • Page 14 To remove all electrical current from the device, ensure that all power cords are disconnected from the power source. CAUTION: Do not place any object weighing more than 82 kg (180 lbs.) on top of rack-mounted devices. ideacentre 300S Series Hardware Maintenance Manual...

  • Page 15: Chapter 3. General Information

    This section lists the physical specifications. Environment Air temperature: Operating: 10° to 35°C Transit: -20° to 55°C Humidity: Operating: 35% to 80% Transit: 20% to 90% (40°C) Altitude: 86KPa to 106KPa Electrical input: Input voltage: 90V-264V(AC) Input frequency: 47Hz-63Hz © Copyright Lenovo 2015...
  • Page 16 300S Series Hardware Maintenance Manual...

  • Page 17: Chapter 4. General Checkout

    • If the computer displays a POST error, go to “POST error codes”. • If the computer hangs and no error is displayed, continue at step 7. 7. If the test stops and you cannot continue, replace the last device tested. © Copyright Lenovo 2015...
  • Page 18 300S Series Hardware Maintenance Manual...

  • Page 19: Chapter 5. Using The Setup Utility

    1. If your computer is already on when you start this procedure, shut down the operating system and turn off the computer. 2. Press and hold the F1 key then turn on the computer. When the Lenovo BIOS Setup Utility program is displayed, release the F1 key.
  • Page 20 5. Select Save changes and Exit from the menu. Power-On Password When a Power-On Password is set, you cannot start the Lenovo BIOS Setup Utility program until a valid password is typed from the keyboard. Setting, changing, or deleting a Power-On Password Note: A password can be any combination of letters and numbers up to 16 character (a-z, and 0-9).

  • Page 21: Enabling Or Disabling A Device

    To set a Power-On Password, do the following: 1. Start the Lenovo BIOS Setup Utility program (See ”Starting the Lenovo BIOS Setup Utility program” on page 13.) 2. From the Security menu, select Set Power-On Password and press the Enter key.

  • Page 22: Selecting A Startup Device

    Agent. 4. Select Disabled or Enabled, and then press the Enter key. 5. Return to the Lenovo BIOS Setup Utility program menu and select the Exit option. 6. Select Save changes and Exit from the menu. Note: If you do not want to save the settings, select Discard changes and Exit from the menu.

  • Page 23: Exiting The Lenovo Bios Setup Utility Program

    Exiting the Lenovo BIOS Setup Utility program After you finish viewing or changing settings, press the Esc key to return to the Lenovo BIOS Setup Utility program main menu. You might have to press the Esc key several times. Do one of the following: •...
  • Page 24 300S Series Hardware Maintenance Manual...

  • Page 25: Chapter 6. Symptom-To-Fru Index

    Check that the following are properly installed: Reseat connectors • Power Cord • On/Off Switch connector • System Board Power Supply connectors • Microprocessor(s) connection Check the power cord. Power Cord Check the power-on switch. Power-on Switch © Copyright Lenovo 2015...

  • Page 26: Post Error Codes

    3. Power-on the computer to re-test the system. 4. Repeat steps 1 through 3 until you find the failing device or component. If all devices and components have been removed and the problem continues, replace the system board. ideacentre 300S Series Hardware Maintenance Manual...

  • Page 27: Chapter 7. Locating Connectors, Controls And Components

    Chapter 7. Locating connectors, controls and components This section provides illustrations to help locate the various connectors, controls and components of the computer. © Copyright Lenovo 2015...
  • Page 28 It provides basic computing functions and supports a variety of devices that are factory-installed or that you can install later. The following illustration shows the location of connectors and components on the front of the motherboard. ideacentre 300S Series Hardware Maintenance Manual...
  • Page 29 ideacentre 300S -11IBR 1. Battery 9. LPC debug header 2. Microprocessor fan header 10. Front panel connector 3. Memory connector 11. Front USB connectors (2) 4. Microprocessor and heat sink 12. M.2 Wi-Fi card slot 13. Front audio connector 5. Clear CMOS jumper 6.
  • Page 30 16. PCI express X 1 adapter slots (2) 7. Auxiliary power connector 17. Front audio connector 8. Battery 18. PCI express X 16 adapter slot 9. SATA connectors (3) 19. System fan header 10. Front panel connector ideacentre 300S Series Hardware Maintenance Manual...

  • Page 31: Chapter 8. Replacing Hardware

    Attention: Do not remove the computer cover or attempt any repair before reading the “Important safety information” in the Safety and Warranty Guide that was included with your computer. To obtain copies of the Safety and Warranty Guide, go to the Support Web site at: http://consumersupport.lenovo.com. Note: Use only parts provided by Lenovo.

  • Page 32: Replacing The Keyboard And Mouse

    Attention: Turn off the computer and wait 3 to 5 minutes to let it cool down before removing the cover. Note: It may be helpful to place the computer face-down on a soft flat surface for this procedure. Lenovo recommends that you use a blanket, towel, or other soft cloth to protect the computer screen from scratches or other damage.

  • Page 33: Removing The Front Bezel

    Step 4. Remove the 2 screws that secure the computer cover at the rear of the chassis. Step 5. To reinstall the computer cover: Line up the computer cover with the chassis, and then slide it back. Secure the computer cover to the chassis with the screws. Removing the front bezel Attention: Turn off the computer and wait 3 to 5 minutes to let it cool down before removing the cover.

  • Page 34: Replacing An Optical Drive

    Note: It may be helpful to place the computer face-down on a soft flat surface for this procedure. Lenovo recommends that you use a blanket, towel, or other soft cloth to protect the computer screen from scratches or other damage.
  • Page 35 Step 6. Remove the 2 screws that secure the optical disk drive bay to the chassis. Step 7. Slide out the optical disk drive bay, and then lift it up. Step 8. Disconnect the data and power cables from the rear of the optical drive. Step 9.

  • Page 36: Replacing The Hard Disk Drive

    Slide out the hard disk drive bay, and then lift it up. Disconnect the data and power cables from the hard disk drive. Step 9. Remove the 4 screws that secure the hard disk drive to the bay. ideacentre 300S Series Hardware Maintenance Manual...

  • Page 37: Replacing A Memory Module

    Step 10. Slide the hard disk drive out of the bay. Step 11. Install the new hard disk drive： Insert the new hard disk drive into the drive bay. Screw back the 4 screws on the drive bay. Attach the data and power cables to the new hard disk drive. Line up the hard disk drive bay, and then slide it in.
  • Page 38 Step 9. For ideacentre 300S-11ISH, refer to the below instructions: Step 10. Remove the memory module being replaced by opening the retaining clips as shown. ideacentre 300S Series Hardware Maintenance Manual...

  • Page 39: Replacing The Adapter

    Step 11. Position the new memory module over the memory connector. Make sure the notch on the memory module is correctly aligned with the connector key on the system board. Push the memory module straight down into the connector until the retaining clips close. Step 12.

  • Page 40: Replacing The Graphic Card

    Refer to “Left and right view” and “Rear view” for help with locating the various connectors. Step 4. Remove the computer cover. Refer to “Removing the computer cover”. ideacentre 300S Series Hardware Maintenance Manual...

  • Page 41: Replacing The Heat-Sink

    Step 5. Disconnect the fan power cable from the connector on the motherboard. Step 6. Remove the 4 screws that secure the microprocessor fan to the heat-sink and lift up the microprocessor fan to remove it. Step 7. To install the new microprocessor fan: Line up the new microprocessor fan with the heat-sink and secure it to the heat-sink with 4 screws.

  • Page 42: Replacing The Cpu

    “Rear view” for help with locating the various connectors. Step 4. Remove the computer cover. Refer to “Removing the computer cover”. Step 5. Replacing the heat-sink assembly. Refer to “Replacing the heat-sink assembly”. ideacentre 300S Series Hardware Maintenance Manual...
  • Page 43 Step 6. To remove the microprocessor from the system board, press then slide the small handle out to spring it up. and open the retainer. Attention: Do not touch the gold contacts on the bottom of the microprocessor. When handing the microprocessor, touch only the sides.

  • Page 44: Replacing The Wi-Fi Card

    “Rear view” for help with locating the various connectors. Step 4. Remove the computer cover. Refer to “Removing the computer cover”. Step 5. Remove the graphic card. Refer to “Replacing the graphic card”. ideacentre 300S Series Hardware Maintenance Manual...

  • Page 45: Replacing The Front Usb/Card Reader/Audio Module

    Step 6. Disconnect the 2 antenna cables from the Wi-Fi card. Step 7. Remove the screw that secure the Wi-Fi card to the motherboard. Step 8. Pull the Wi-Fi card upward to remove it from the card port. Step 9. Install the new Wi-Fi card: Line up the new Wi-Fi card, and then insert it into the same card port.

  • Page 46: Replacing The Motherboard

    Step 10. Remove the heat-sink. Refer to “Replacing the heat-sink”. Step 11. Remove the graphic card. Refer to “Replacing the graphic card”. Step 12. Remove the Wi-Fi card. Refer to “Replacing the Wi-Fi card”. ideacentre 300S Series Hardware Maintenance Manual...
  • Page 47 Step 13. Disconnect the all cables from the connectors on motherboard. Step 14. Remove the 5 screws that secure the motherboard to the chassis. Step 15. Lift up the motherboard to remove it. Step 16. Install the new motherboard: Line up the holes on the new motherboard with mounting holes on the chassis and secure it with screws.
  • Page 48 300S Series Hardware Maintenance Manual...

  • Page 49: Fru Lists-H30-05

    GX 2H285 SATA cable,angle,No Latch(R) CABLE 31049512 Volex 1.8M C13 ITY power cord CABLE 31049516 Volex 1.8M C13 SWI power cord CABLE 31039728 Longwell 1.8M Israel C13 power cord(R) CABLE 31033857 LW BLK1.0m3wire ULCSA power cord(R) CABLE © Copyright Lenovo 2015...
  • Page 50 Volex 1.0M C5 SA power cord CABLE 31026350 LW BLK1.8m ANE Power Cord(R) CABLE 31032989 LS 2H285 SATA cable,angle,No Latch(R) CABLE 31049515 Volex 1.8M C13 LA power cord CABLE 31038784 LW BLK 1.8m Brazil power cord(R) CABLE ideacentre 300S Series Hardware Maintenance Manual...
  • Page 51 31039100 LW BLK 1.0m Argentina C5 power cord(R) CABLE 31026349 LW BLK1.8m BSMI Power Cord(R) CABLE 31049513 Volex 1.8M C13 BR power cord CABLE 31049500 Volex 1.0M C5 ANZ power cord CABLE 31507414 LS USB2.0 F_IO cable_U500A600_326CT CABLE 31043152 GS 400mm SATA cable 1 latch L_angle CABLE 31049517 LX(ASAP) 1.0M C5 UL power cord...
  • Page 52 Sunrex EKB-10YA(RU) B-Silk USB KB-LVT8 KYB_MOUSE 25209200 Liteon SK-8861(EN-FR) 2.4G KB-Black8 KYB_MOUSE 25209187 Liteon SK-8861(CH) 2.4G KB-Black8 KYB_MOUSE 25209129 Sunrex EKB-10YA(HB) B-Silk USB KB-LVT8 KYB_MOUSE 25209195 Liteon SK-8861(GR) 2.4G KB-Black8 KYB_MOUSE 25209197 Liteon SK-8861(BG) 2.4G KB-Black8 KYB_MOUSE ideacentre 300S Series Hardware Maintenance Manual...
  • Page 53 25209134 Sunrex EKB-10YA(KR) B-Silk USB KB-LVT8 KYB_MOUSE 25209136 Sunrex EKB-10YA(EN-FR) B-S USB KB-LVT8 KYB_MOUSE 25209126 Sunrex EKB-10YA(SP) B-Silk USB KB-LVT8 KYB_MOUSE 25209190 Liteon SK-8861(ES) 2.4G KB-Black8 KYB_MOUSE 25209114 Sunrex EKB-10YA(TW) B-Silk USB KB-LVT8 KYB_MOUSE 25209124 Sunrex EKB-10YA(GE) B-Silk USB KB-LVT8 KYB_MOUSE 25209179 Liteon SK-8861(CS-SK) 2.4G KB-Black8...
  • Page 54 PWR_SUPPLY 36200353 Liteon PA-1650-72IA Common 65W adapter PWR_SUPPLY 00XD080 Braswell MB Rear IO shield SHIELD 00PC564 NV GF GT720 1G VGA/HDMI LP VIDEO_CARD 00PC522 NV GF GT720 2G VGA/HDMI LP VIDEO_CARD 00JT454 Wireless,CMB,LTN,8821AE WIRELESS ideacentre 300S Series Hardware Maintenance Manual...
  • Page 55 00JT497 Wireless,CMB,IN,3165 ac WIRELESS 00JT507 Wireless,CMB,IN,3165 ac Ind WIRELESS FRU list of ideacentre 300S-11IBR CRU No. Side cover Memory Front cover ODD cable ODD bracket HDD cable HDD bracket TF Reader FRU=TF board+ TF cable TF board TF cable Fan FRU=Fan+Heat sink Heat sink RF Antenna FRU=RF cable+Antenna+Adhesive Rf cable...
  • Page 56 Power switch (with cable) USB&Audio FRU=USB&Audio Bracket+USB&Audio module USB&Audio Bracket USB&Audio module (with cable) Mechanical chassis cable organizer rubber foot*3 Mother board FRU=Mother board+Cmos battery+Thermal paste Mother board CPU Holder Cmos battery Thermal paste ideacentre 300S Series Hardware Maintenance Manual...
  • Page 57 I/O shieding power cord organizer Conductive foam Power shielding Graphic board Graphic bracket Power supply Thermal Cable Chapter 8 Replacing hardware...
  • Page 58 300S Series Hardware Maintenance Manual...

  • Page 59: Chapter 9. General Information

    • Wake Up on Alarm: You can specify a date and time at which the computer will be turned on automatically. This can be either a single event , a daily event or a weekly event. • Wake Up on LAN: This feature allows LAN adapter card to wake the System. © Copyright Lenovo 2015...

Table of Contents