Table of Contents
Advertisement
INSTALLATION AND OPERATING INSTRUCTIONS
WARNING: If the information in this manual is not followed exactly, a fire or
explosion may result causing property damage, personal injury or loss of life.
-- Do not store or use gasoline or other flammable vapours and liquids in the
vicinity of this or any other appliance.
-- WHAT TO DO IF YOU SMELL GAS
- Do not try to light any appliance.
- Do not touch any electrical switch; do not use any phone in your building.
- Immediately call your gas supplier from a neighbour's phone. Follow the
- If you cannot reach your gas supplier, call the fire department.
--Installation and service must be performed by a qualified installer, service
agency or the gas supplier.
021100-20
SERIES B
gas supplier's instructions.
IMPORTANT: THESE INSTRUCTIONS
ARE TO REMAIN WITH THE
HOMEOWNER
MIR-DVB1
5056.3
Advertisement
Table of Contents
Related Manuals for Pacific energy B Series
Summary of Contents for Pacific energy B Series
- Page 1 SERIES B INSTALLATION AND OPERATING INSTRUCTIONS WARNING: If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury or loss of life. -- Do not store or use gasoline or other flammable vapours and liquids in the vicinity of this or any other appliance.
-
Page 2: Table Of Contents
Contents CAUTION ..................3 SAFETY ..................3 MAINTENANCE ................3 VALVE ASSEMBLY ............... 4 GAS SUPPLY................. 6 ELECTRICAL ................. 6 CLEARANCES ................6 INSTALLATION PRECAUTIONS ..........7 MANUFACTURED (MOBILE) HOME ..........7 STRAIGHT THROUGH WALL ............8 CORNER INSTALLATION ............. 9 BASEMENT INSTALLATION ............ -
Page 3: Caution
CAUTION It is Pacific Energy’s policy that no responsibility is assumed by FOR YOUR SAFETY - Do not install or operate your Pacific Energy the Company or by any of its employees or representatives for Mirage Direct Vent without first reading and understanding this any damages caused by an inoperable, inadequate, or unsafe manual. -
Page 4: Valve Assembly
VALVE ASSEMBLY Caution: Before making wiring connections, ensure all power is disconnected! Open the carton that contains the valve assembly and inspect all components for damage. Do Not install if damaged. Remove 4) The gas connection may now be made. See "GAS SUPPLY" packaging tape from right side door on unit and swing side panel section for details. - Page 5 Optional Blower Wiring Fig. # 3 Connect Here Fig. # 4 Optional Wall Switch or Wall thermostat...
-
Page 6: Gas Supply
GAS SUPPLY CLEARANCES Caution: The gas line should be installed by a qualified service The minimum clearances from the appliance to combustibles are person in accordance with all building codes. Consult local and/ shown on Fig. # 6. For purpose of servicing, a 12" right side (side with or national building codes before proceeding. -
Page 7: Installation Precautions
INSTALLATION PRECAUTIONS CAUTION: UNDER NO CONDITION SHOULD COMBUSTIBLE MATERIAL BE CLOSER THAN 1-INCH FROM THE VERTICAL The Mirage Gas Appliance installation and venting must con- AND HORIZONTAL SECTIONS OF THIS VENT SYSTEM. form to the current CAN/CGA-B149 installation code (in Canada) or the current National Fuel Gas Code, ANSI Z223.1 (in the USA), and approved per local codes. -
Page 8: Straight Through Wall
Fig. # 8 STRAIGHT THROUGH WALL pipe over top of the collar up to the crimp-bead and attach with three sheet metal screws. Seal the joint with high temperature silicone. Next, slide the 7-inch outer pipe over the 5-inch pipe fully and secure to the pipe collar with three sheet metal screws. -
Page 9: Corner Installation
CORNER INSTALLATION 1) Determine the exact position of the gas stove, making sure the unit will be set at 45° to the walls and the corner clearance will not be less then 1-inch. The vent pipe should be centred (if possible) between two building members. - Page 10 Fig. # 11...
-
Page 11: Basement Installation
BASEMENT INSTALLATION 4) The starter pipe (SK 18 or SK 24) must be the last section in the vent system. The pipe may have to be cut to length depending on the 1) In planning a basement installation it is necessary to determine wall thickness and/or position of vent system. -
Page 12: Vent Terminal Installation
VENT TERMINAL INSTALLATION Fig. # 14 NOTE: THE VENT TERMINAL MUST BE POSITIONED SO THAT THE FLUE OUTLET IS POINTING UP. 1) Install the vent terminal backing plate on the outside wall. (see Fig. #14) When placing the backing plate, make sure the 7" collar inserts into the corresponding vent pipe. -
Page 13: Log Set
LOG SET Fig. # 15 The log set comes installed in the appliance from the factory. If the Back Log logs have to be removed for cleaning, they must be handled carefully as they are very fragile. To reinstall the log set, follow this procedure: 1) Place the back log on the rear tabs of the burner assembly, with flat side facing rear and bark side forward. -
Page 14: Lighting Instructions
FOR YOUR SAFETY READ BEFORE LIGHTING WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. A. This appliance has a pilot which must be lighted by hand. - If you cannot reach your gas supplier, call the fire depart- When lighting the pilot, follow these instructions exactly. -
Page 15: First Fire
FIRST FIRE FLAME ADJUSTMENT When lit for the first time, the appliance will emit a slight odour for a The air shutter on the burner venturi tube controls the primary couple of hours. This is due to the curing of paints, sealants and combustion air to the gas burner. -
Page 16: Replacement Parts
....OPTIONAL BLOWER (not shown) ..MFSD.BLOW All parts may be ordered from your nearest Pacific Energy dealer. Contact Pacific Energy for the location of the dealer nearest you. When ordering parts, please specify appropriate finish code. Codes are as follows: Porcelain Finish Black .. - Page 17 Fig. # 20...
- Page 18 -NOTES-...
- Page 19 Pacific Energy Fireplace Products Ltd. Duncan, British Columbia, Canada Certified for Canada and U.S.A. / REPORT NO. 6563 Certifié pour Canada et U.S.A. (JUNE 93) Made in Canada / Fabrique au Canada MODEL/ SERIES/ MIRAGE DV MODELE: SERIE: FOR USE WITH/...
- Page 20 Pacific Energy Fireplace Products Ltd. Box 1060, Duncan, B.C. V9L 3Y2 Phone: 250-748-1184 Web site: http://www.pacificenergy.net Printed in Canada...