Advertisement
Quick Links
A B B M E A S U R E M E N T & A N A LY T I C S
Wi-Fi
Antenna kit installation guide
®
Introduction
This document will define the procedures and list the parts required to
install a Wi-Fi antenna.
IMPORTANT NOTE: To enable and configure Wi-Fi for secure
access, refer to the XSeries
Secure and easy wireless
access for configuration.
Measurement made easy
G5
XFC or XRC user manuals.
Advertisement
Related Manuals for ABB 2106049
Summary of Contents for ABB 2106049
- Page 1 A B B M E A S U R E M E N T & A N A LY T I C S Wi-Fi Antenna kit installation guide ® Secure and easy wireless access for configuration. Measurement made easy Introduction This document will define the procedures and list the parts required to install a Wi-Fi antenna.
-
Page 2: Additional Information
ABB Inc. and its affiliates are not liable for damages and/or losses related to such security breaches, any unauthorized access, interference, intrusion, leakage and/or theft of data or information. -
Page 3: Safety Symbol Conventions
Safety Observe warning signs on packaging and on the devices, prior to software configuration. Safety symbol conventions The following conventions are used throughout this document to bring attention to important information: "NOTICE" hazards are associated with equipment or property damage, it must be understood that under certain operating conditions, operating damaged equipment can result in degraded system / process performance leading to serious or life-threatening injuries. - Page 4 Overview The photo below shows the Wi-Fi antenna kit parts. Figure 1: Wi-Fi antenna kit parts Part number 2106049 kit contents Photo # Name Photo # Name SMA Fittings Surge protector Antenna SMA plug-to-jack adapter Terminator plug Cable assembly FCC IC tag...
-
Page 5: Installation Procedures
IMPORTANT NOTE: The cable used in the following procedure is included in the kit. Specify by number the required length when ordering the kit. Installation procedures Locate the cable clamp on the upper right corner of the board. Put the straight end of the cable assembly through the cable clamp. - Page 6 Attach the plug-to-jack adapter Attach the surge protector to the straight SMA fitting of the to the plug-to-jack adapter. cable. Figure 4: Attach the straight Figure 5: Attach the surge SMA fitting protector Figure 4: Figure 5: Cut the ground cable to length. Strip ⅜ inch of insulation from the free end.
- Page 7 11. Identify the enclosure used and the location of the antenna hole. IMPORTANT NOTE: The 8 AH, 13 AH, 16 AH, and 26 AH batteries fit in the 6410 enclosure with the antenna surge protector installed. Enclosure number Antenna hole location Photo of enclosure 6410 On the Left side of the...
- Page 8 Enclosure number Antenna hole location Photo of enclosure 6713 2 holes are on the bottom of the enclosure in the back left corner. There is a 3rd hole of same size in the Back Right Corner. The Cable assembly is not long enough to reach that hole.
- Page 9 Figure 9: Inside the enclosure 15. Attach the ground cable to the ground post (see number 2 in the picture below). 16. Route the cable assembly via mountable cable ties attached to the enclosure (see number 1, below). Figure 10: Cable assembly Photo Name number...
- Page 10 Figure 11: FCC compliance tag 18. Remove the red protective cap from the surge protector. 19. Attach the antenna to the surge protector. Keep the Antenna in the straight position (see below). Figure 12: Straight antenna 20. Attach the terminator plug to the board ANT-2, connector (J43). (see number 1, below).
- Page 11 This page is intentionally blank. 2106123MNAA | WI-FI ANTENNA KIT | 11...
- Page 12 We reserve the right to make technical changes or modify the contents of this document without prior notice. With regard to purchase orders, the agreed particulars shall prevail. ABB does not accept any responsibility whatsoever for potential errors or possible lack of information in this document.