Table of Contents
Advertisement
Quick Links
HP FlexFabric 11900 2500W AC
Power Supply User Guide
Part number: 5998-4091
Power supply overview
The AC2500 (JG616A) is a power supply with AC input and DC output. It can provide up
to 2500 W DC output.
The AC2500 has the following features:
Feature
Protection function
Support for hot
swapping
Support for
redundancy
CAUTION:
AC2500 cannot work with other models of power supplies in the same device.
•
When the temperature of the power supply is higher than the upper limit of the
•
operating temperature, the power supply automatically shuts down. When the
temperature falls into the normal range, the power supply automatically starts.
Description
Protection for under-voltage input, over-voltage input,
over-voltage output, output short circuit, under-current
output, over-current output, and overheat.
You can plug in or unplug the power supply when the
device is operating properly.
The power supplies can operate in N+1 or N+N redundant
mode. For more information, see
configuration."
1
"Power supply
Advertisement
Table of Contents
Related Manuals for HP FlexFabric 11900 2500W AC
Summary of Contents for HP FlexFabric 11900 2500W AC
-
Page 1: Power Supply Overview
HP FlexFabric 11900 2500W AC Power Supply User Guide Part number: 5998-4091 Power supply overview The AC2500 (JG616A) is a power supply with AC input and DC output. It can provide up to 2500 W DC output. The AC2500 has the following features:... -
Page 2: Front Panel
Front panel Figure 1 Front panel of AC2500 (1) Captive screw (2) Power supply handle (3) Power input jack (4) Power output status LED (5) Power input status LED LEDs A power supply has two status LEDs. The following table lists the LED status and description. -
Page 3: Technical Specifications
Sign Color Description Green The power output is normal. The power supply encounters exceptional power output problems. In other words, when output short circuit, over-current output, Power over-voltage output, under-voltage input, or output remote shutdown occurs, the power supply enters the protected state. The temperature of the power supply is too Orange high, and the power supply enters the... -
Page 4: Power Supply Configuration
Power supply configuration You can determine the number of power supplies to be configured for the system according to the actual power consumption and power supply conditions. In an environment with two mains power inputs, you can configure N+N redundant •... -
Page 5: Installing The Power Supply
Figure 2 Installation flow of a power supply NOTE: The device needs at least one power supply to provide power supply, so the chassis has a power supply slot without a blank panel. For this slot, you can skip "Remove the blank panel"... - Page 6 Figure 3 Removing the blank panel (1) Unfasten the captive screws on the blank panel (2) Remove the blank panel Unpack the power supply. Holding the handle of the power supply with one hand and supporting the bottom of the power supply with the other, slide the power supply along the guide rails into the slot.
-
Page 7: Connecting The Power Cord
Figure 4 Installing the power supply into a vertical slot Press the handle back into the notch of the power supply. Use the Phillips screwdriver to fasten the captive screw on the handle to secure the power supply. Connecting the power cord WARNING! Make sure each power cord has a separate circuit breaker. -
Page 8: Removing A Power Supply
NOTE: The cabling rack position varies by switch model. Route the cable as required. For how to fasten the power cord connected to a vertically-installed power supply, Figure 5 Figure 5 Fastening the power cord connected to a vertically-installed power supply Plug the other end of the power cord into an AC power receptacle of the power source, and turn on the connected circuit breaker. - Page 9 Figure 6 Removal flow of a power supply NOTE: The device needs at least one power supply to provide power supply, so the chassis has a power supply slot without a blank panel. For this slot, you can skip "Install the blank panel"...
-
Page 10: Removing The Power Supply
Removing the power supply Use the Phillips screwdriver to unfasten the captive screw on the power supply. Hold the captive screw and pull out the handle of the power supply. As shown in Figure 7, grasp the handle of the power supply with one hand and pull it out a little, support the bottom of the power supply with the other hand, and then pull the module slowly along the guide rails out of the slot. - Page 11 © Copyright 2012 Hewlett-Packard Development Company, L.P. The information in this document is subject to change without notice. BOM: 3101A0GB Version: APW100 5998-4091...