hit counter code
Sony HCD-GTR88 Service Manual
  1. Manuals
  2. Brands
  3. Sony Manuals
  4. Stereo System
  5. HCD-GTR88
  6. Service manual

Sony HCD-GTR88 Service Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

SERVICE MANUAL
Ver. 1.0 2010.04
• HCD-GTR88 is the amplifi er, USB, CD player,
tuner and tape deck (only E4 Model) section in
MHC-GTR88.
Amplifi er section
The following are measured at
Mexican model:
AC 127 V, 60 Hz
Other models:
AC 120 V, 220 V, 240 V, 50/60 Hz
Front/Satellite Speaker
Power Output (rated):
200 W + 200 W (at 6 , 1 kHz,
1% THD)
Front Speaker
RMS output power (reference):
345 W + 345 W (per channel at 8 ,
1 kHz)
Satellite Speaker
RMS output power (reference):
140 W + 140 W (per channel at 24 ,
1 kHz)
Subwoofer
RMS output power (reference):
200 W + 200 W (per channel at 6 ,
100 Hz)
Inputs
PC (AUDIO IN) L/R
Voltage 700 mV, impedance 47 kilohms
MIC
Sensitivity 1 mV, impedance 10 kilohms
(USB) port: Type A
Outputs
PHONES
Accepts headphones of 8 or more
Sony Corporation
9-890-544-01
2010D08-1
Audio & Video Business Group
©
2010.04
Published by Sony EMCS (Malaysia) PG Tec
Photo: HCD-GTR88 (E4 Model)
Model Name Using Similar Mechanism
CD Section
CD Mechanism Type
Optical Pick-up Name
Model Name Using Similar Mechanism
Tape Deck Section
(only for E4 Model)
Tape Mechanism Type

SPECIFICATIONS

USB section
Supported bit rate
MP3 (MPEG 1 Audio Layer-3):
32 kbps – 320 kbps, VBR
WMA: 48 kbps – 192 kbps
AAC: 48 kbps – 320 kbps
Sampling frequencies
MP3 (MPEG 1 Audio Layer-3):
32 kHz/44.1 kHz/48 kHz
WMA: 44.1 kHz
AAC: 44.1 kHz
Transfer speed
Full-Speed
Supported USB device
Mass Storage Class
Maximum current
500 mA
Disc player section
System
Compact disc and digital audio system
Laser Diode Properties
Emission Duration: Continuous
Laser Output*: Less than 44.6 W
* This output is the value measurement
at a distance of 200 mm from the
objective lens surface on the Optical
Pick-up Block with 7 mm aperture.
Frequency response
20 Hz – 20 kHz
Signal-to-noise ratio
More than 90 dB
Dynamic range
More than 88 dB
HCD-GTR88
Tape deck section
(For African model only)
Recording system
4-track 2 channel, stereo
Tuner section
FM stereo, FM/AM superheterodyne tuner
FM tuner section
Tuning range
North American and Brazilian models:
87.5 MHz – 108.0 MHz (100 kHz step)
Other models:
87.5 MHz – 108.0 MHz (50 kHz step)
Antenna
FM lead antenna
Antenna terminals
75 ohms unbalanced
Intermediate frequency
10.7 MHz
AM tuner section
Tuning range
Pan American and Oceanian models:
530 kHz – 1,710 kHz (with 10 kHz tun-
ing interval)
531 kHz – 1,710 kHz (with 9 kHz tuning
interval)
Other models:
530 kHz – 1,610 kHz (with 10 kHz tun-
ing interval)
531 kHz – 1,602 kHz (with 9 kHz tuning
interval)
Antenna
AM loop antenna, external antenna
terminal
Intermediate frequency
450 kHz
COMPACT DISC DECK RECEIVER
E Model
Australian Model
HCD-GTZ4/GTZ4i/GTZ5
CDM88BL-DVBU101
KHM-313CAB/C2NP
HCD-GT111/GT222/GT444/GT555
CS-21SC-900TP
General
Power requirements
Oceanian model: AC 230 V – 240 V,
50/60 Hz
Mexican model: AC 127 V, 60 Hz
Argentina model: AC 220 V, 50/60 Hz
Other models: AC 120 V, 220 V or
230 V – 240 V, 50/60 Hz, Adjustable
with voltage selector
Power consumption: 460 W
Dimensions (w/h/d) (excl. speakers)
(Approx.)
231 mm × 361 mm × 518 mm
Mass (excl. speakers) (Approx.)
African and Pan Asian models: 16.2 kg
Other models: 15.7 kg
Design and specifi cations are subject to
change without notice.
•
Abbreviation
E4 : African model

Advertisement

Table of Contents
loading

Related Manuals for Sony HCD-GTR88

Summary of Contents for Sony HCD-GTR88

  • Page 1: Specifications

    HCD-GTR88 SERVICE MANUAL E Model Australian Model Ver. 1.0 2010.04 • HCD-GTR88 is the amplifi er, USB, CD player, tuner and tape deck (only E4 Model) section in MHC-GTR88. Photo: HCD-GTR88 (E4 Model) Model Name Using Similar Mechanism HCD-GTZ4/GTZ4i/GTZ5 CD Section...

  • Page 2: Table Of Contents

    WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. ELECTRICAL PARTS LIST ....... 62 REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.

  • Page 3: Servicing Notes

    Therefore, when checking the laser diode emission, observe from more than 30 cm away from the objective lens. Model Part No. UNLEADED SOLDER HCD-GTR88: E2, E51 4-164-385-0[] Boards requiring use of unleaded solder are printed with the lead- HCD-GTR88: AR 4-164-385-1[] free mark (LF) indicating the solder contains no lead.
  • Page 4 HCD-GTR88 HOW TO OPEN THE TRAY WHEN POWER SWITCH TURN OFF Step: 1) Work after removing the case (side-R and side-L) referring to “2.2. CASE (SIDE-L/R)” on disassembly (page 6). 2) Work after removing the top case referring to “2-3. TOP CASE” on disassembly (page 6).

  • Page 5: Disassembly

    HCD-GTR88 SECTION 2 DISASSEMBLY • This set can be disassembled in the order shown below. 2-1. DISASSEMBLY FLOW 2-2. CASE (SIDE-L/R) (Page 6) 2-3. TOP CASE (Page 6) 2-5. FRONT PANEL BLOCK, HUB BOARD, DMB19 BOARD 2-4. TAPE MECHANISM DECK (FOR AFRICAN MODEL ONLY)

  • Page 6: Case (Side-L/R)

    HCD-GTR88 2-2. CASE (SIDE-L/R) 2 three screws (BVTP3 K 10) Tape deck section (For African model only) 2 three screws (BVTP3 K 10) 1 four screws (case 3 TP2) 4 case (side-L) 1 four screws 4 case (side-R) (case 3 TP2) 2-3.

  • Page 7: Tape Mechanism Deck (For African Model Only)

    HCD-GTR88 2-4. TAPE MECHANISM DECK (FOR AFRICAN MODEL ONLY) 5 two screws 6 bracket (deck) (BVTP2.6 K8) 4 TC board 7 two screws (BVTP2.6 K8) 3 two screws (BVTP3 K 8) 1 CN501 (8P) 9 tape mechanism deck 2 Cut the clamp.

  • Page 8: Dc Fan (M101)

    HCD-GTR88 2-6. DC FAN (M101) 1 four screws (BVTP3 K 8) 2 cover fan (GVX7S) 5 CN600 (3P) 3 two screws (BVTP3 K 8) 4 DC fan (M101) 2-7. BACK PANEL, SUBTRANS BOARD qk clamp filter (ferrite core) qf Bracket (Subtrans)

  • Page 9: Main Board

    HCD-GTR88 2-8. MAIN BOARD 3 CN200 (12P) 2 CN100 (10P) 4 CN550 (6P) 1 three screws (BVTP3 5 MAIN board 2-9. DC FAN (M101), PT SHIELD BOARD, POWER AMP BOARD SECTION qa one screw (BVTP3 K 8) 7 two screws...

  • Page 10: 2-10. Power Amp Board, Subwoofer Board

    HCD-GTR88 2-10. POWER AMP BOARD, SUBWOOFER BOARD 2 one screw (BVTP3 K 8) 1 one screw (BVTP3 K 8) 5 POWER AMP board 3 two screws (transistor) 4 CN803 (7P) 8 heat sink 6 two screws (BVTP3 K 8) 7 Bracket (PWB)

  • Page 11: Cd Mechanism Block (Cdm88Bl-Dvbu101)

    HCD-GTR88 2-12. CD MECHANISM BLOCK (CDM88BL-DVBU101) 8 one screw (BVTP3 K8) 9 cover dust (CDM88-A-top) 8 one screw (BVTP3 K 8) q; CD mechanism block (CDM88BL-DVBU101) 7 three sheets (CDM) 3 bracket (MTK) 2 one screw (BVTP3 K8) 1 wire (flat type) (13 core)

  • Page 12: Belt (Dlm3A)

    HCD-GTR88 2-14. BELT (DLM3A) position of belt belt 3 cover 2 four screws belt 4 two belts (DLM3A) state of opening the CD tray 1 Turn a gear till a lever rises up to the position of the figure. lever...

  • Page 13: Test Mode

    HCD-GTR88 SECTION 3 TEST MODE PANEL TEST MODE 2. Press [EQ BAND/SURROUND] button repeatedly until a message “GEQ MIN” appears on the fl uorescent indicator This mode is used to check the fl uorescent indicator tube, LEDs, tube. GEQ decreases to its minimum.
  • Page 14 HCD-GTR88 CD SHIP MODE (WITHOUT MEMORY CLEAR) METER TEST MODE This mode moves the optical pick-up to the position durable to This mode is used to check the meter device. vibration. Use this mode when returning the set to the customer Procedure: after repair.

  • Page 15: Mechanical Adjustments

    HCD-GTR88 SECTION 4 MECHANICAL ADJUSTMENTS (For African model only) PRECAUTION 1. Clean the following parts with a denatured-alcohol-moistened swab : record/playback head pinch roller erase head rubber belts capstan idlers 2. Demagnetize the record/playback head with a head demag- netizer. (Do not bring the head magnetizer close to the erase head.)

  • Page 16: Electrical Adjustments

    HCD-GTR88 SECTION 5 ELECTRICAL ADJUSTMENTS 2. Turn the adjustment screw and check output peaks. If the peaks TUNER SECTION do not match for L-CH and R-CH, turn the adjustment screw FM TUNE LEVEL CHECK so that outputs match within 1dB of peak.
  • Page 43 HCD-GTR88 • Waveforms — DMB19 BOARD — — MAIN BOARD — — HUB BOARD — IC101 0 (XTALO) IC401 qa (XC-OUT) IC1501 es (XTAL2) 216.7 mVp-p 2.67 Vp-p 4.5 Vp-p 58.6 ns 29.3 ns 20 ms 100 mV/DIV, 20 ns/DIV...

  • Page 44: Ic Block Diagrams

    HCD-GTR88 • IC Block Diagrams IC1101 PT6324-Q (DISPLAY Board) CONTROL SERIAL DISPLAY DATA MEMORY INTERFACE DOUT SEGMENT DRIVER TIMING GENERATOR KEY MATRIX MEMORY SG24 GRID SG23 DRIVER DIMMING SG22 CIRCUIT SG1/KS1 SG21 SG2/KS2 SG20 SG19 SG3/KS3 SG4/KS4 SG18 14 15 16 17 18 19 20 21 22 23 24 25 26 IC107 TK11133CSCL-G (DMB19 Board (1/3)) OVER HEAT &...
  • Page 45 HCD-GTR88 IC201 FAN8036L (DMB19 Board (2/3)) (GND) REGVCC IN1- DO1- DO2+ OUT1 IN2+ DO2- IN2- PGND1 REGVCC REGVCC REGC1 OUT2 REGC2 RES1 REGVCC REGVCC (GND) (GND) RES2 DO3+ DO3- REGCTL DO4+ IN3+ DO4- IN3- PGND2 CUT3 DO5+ IN4+ MUTE123 MUTE4...
  • Page 46 HCD-GTR88 IC4602 CS4335-KSZR (DMB19 Board (3/3)) AOUTL SERIAL INPUT VOLTAGE INTERPOLATOR INTERPOLATOR SDATA INTERFACE REFERENCE AGND DEM/SCLK ANALOG LRCK LOW-PASS MODULATOR FILTER DE-EMPHASIS ANALOG LOW-PASS AOUTR MODULATOR FILTER MCLK IC251 NJM4558V-TE2 (MAIN Board (2/3)) IC1500 NJM2903V (TE2) (HUB Board) IC252 NJM4558V-TE2 (MAIN Board (2/3))
  • Page 47 HCD-GTR88 IC400 R2A15216FP (MAIN Board (2/3)) REFERENCE INDR INDL 6 INPUT 6 INPUT INER SELECTOR SELECTOR INEL (R-CH) (L-CH) INFR INFL GAMER GAMEL INGAINOUTR INGAINOUTL RECAR RECAL RECBR RECBL VOCAL CUT SURROUND OR DPL IN TRER TREL TONE TONE MID1R...
  • Page 48 HCD-GTR88 • IC Pin Function Description DMB19 BOARD (1/3) IC101 CXD9968R (LE) (RF AMP, SERVO DSP, AUDIO PROCESSOR) Pin No. Pin Name Description RF_A RF main beam (C) input from the optical pick-up block RF_B RF main beam (B) input from the optical pick-up block...
  • Page 49 HCD-GTR88 Pin No. Pin Name Description Bank address signal output to the SD-RAM DVSS18 Ground terminal Bank address signal output to the SD-RAM 81 to 83 RA10, RA0, RA1 Address signal output to the SD-RAM DVDD33 Power supply terminal (+3.3V)
  • Page 50 HCD-GTR88 HUB BOARD IC1501 USB2512A-AEZG (USB CONTROLLER) Pin No. Pin Name Description USBDN1_DM, 1, 2 Audio serial data input from the USB A connector USBDN1_DP USBDN2_DM, 3, 4 Two-way audio serial data with the USB B connector USBDN2_DP VDDA33 Power supply terminal (+3.3V)
  • Page 51 HCD-GTR88 MAIN BOARD (1/3) IC401 R5F3640DDFA (SYSTEM CONTROLLER) Pin No. Pin Name Description FL-DRIVER-CLK Serial data clock signal to FL Driver, PT6324 FL-DRIVER-DATA Serial data output signal to FL Driver, PT6324 AD SUPPLY SWITCH AD Power Control pin SIRCS Remote control signal input...
  • Page 52 HCD-GTR88 Pin No. Pin Name Description R2A15216FP-DATA Serial data output to audio signal processor, R2A15216FP FR SPK RELAY Relay drive signal output for the front speakers "H":relay on STK MUTE Power amplifi er on/off control signal output "H": amplifi er on PROTECT Speaker protect detection signal input from speaker protect circuit "H":protector on...

  • Page 53: Exploded Views

    HCD-GTR88 SECTION 7 EXPLODED VIEWS Note: • -XX and -X mean standardized parts, so • Color Indication of Appearance Parts Ex- The components identifi ed by mark 0 they may have some difference from the ample: or dotted line with mark 0 are critical for original one.

  • Page 54: Top Panel Section

    HCD-GTR88 7-2. TOP PANEL SECTION not supplied not supplied not supplied not supplied TC board FFC502 not supplied (TC board) not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-087-053-01 +BVTP 2.6 (3CR) (E4) 1-797-575-11...

  • Page 55: Loading Panel Section, Hub Board Section, Dmb19 Board Section

    HCD-GTR88 7-3. LOADING PANEL SECTION, HUB BOARD SECTION, DMB19 BOARD SECTION not supplied back panel section CD mechanism section (CDM88B-DVBU101) not supplied not supplied not supplied not supplied DISPLAY board section not supplied supplied not supplied not supplied Note: If wire (fl at type) is replaced, install it after bending it in the same form as that before replacement.

  • Page 56: Display Board Section

    HCD-GTR88 7-4. DISPLAY BOARD SECTION not supplied (DISPLAY board) S1301 not supplied (VOL board) supplied with S1301 not supplied front panel section Note: If wire (fl at type) is replaced, install it after bending it in the same form as that before replacement.

  • Page 57: Front Panel Section

    HCD-GTR88 7-5. FRONT PANEL SECTION supplied supplied not supplied (MIC board) not supplied not supplied (USB board) not supplied Ref. No. Part No. Description Remark 2-895-507-01 KNOB (MIC) X-2541-955-1 FRONT PANEL ASSY (GVX-COM) (EXCEPT E4) X-2546-463-1 FRONT PANEL ASSY (GVX-E4) (E4)

  • Page 58: Back Panel Section

    HCD-GTR88 7-6. BACK PANEL SECTION not supplied (SUBTRANS board) not supplied M101 not supplied MAIN board section Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 0 257 1-828-952-11 WIRE (FLAT TYPE) (9 CORE) 1-835-068-21 CORD, POWER (AUS)

  • Page 59: Main Board Section

    HCD-GTR88 7-7. MAIN BOARD SECTION not supplied (POWER AMP board (EXCEPT MX) POWER7 AMP board (MX)) not supplied M101 not supplied not supplied (SUBWOOFER board) supplied chassis section not supplied (PT SHIELD board) Note: If wire (fl at type) is replaced, install it after bending it in the same form as that before replacement.

  • Page 60: Chassis Section

    HCD-GTR88 7-8. CHASSIS SECTION F1253 F1251 F1252 F1250 not supplied (TRANS board) PT1250 not supplied not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 0 PT1250 4-225-252-01 CUSHION (FOOT) 1-445-825-11 POWER TRANSFORMER (MX) 0 F1250...

  • Page 61: Cd Mechanism Section (Cdm88Bl-Dvbu101)

    HCD-GTR88 7-9. CD MECHANISM SECTION (CDM88BL-DVBU101) not supplied (including sled motor, spindle motor) not supplied (spindle motor) not supplied not supplied (sled motor) not supplied not supplied Note: If wire (fl at type) is replaced, install it after bending it in the same form as that before replacement.

  • Page 62: Electrical Parts List

    HCD-GTR88 SECTION 8 DISPLAY ELECTRICAL PARTS LIST Note: • Due to standardization, replacements in • CAPACITORS When indicating parts by reference num- the parts list may be different from the uF: aF ber, please include the board name. parts specifi ed in the diagrams or the com- •...
  • Page 63 HCD-GTR88 DISPLAY DMB19 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R1107 1-218-867-11 METAL CHIP 6.8K 0.5% 1/10W S1118 1-771-410-21 SWITCH, TACTILE (TUNER/BAND) R1108 1-216-833-11 METAL CHIP 1/10W S1119 1-771-410-21 SWITCH, TACTILE (TAPE /PC) R1113 1-216-819-11...
  • Page 64 HCD-GTR88 DMB19 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C198 1-165-908-11 CERAMIC CHIP 1uF < DIODE > C199 1-162-968-11 CERAMIC CHIP 0.0047uF D001 6-500-848-01 DIODE MC2840-T112-1 C203 1-162-970-11 CERAMIC CHIP 0.01uF D002 6-500-848-01 DIODE MC2840-T112-1...
  • Page 65 HCD-GTR88 DMB19 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R123 1-216-809-11 METAL CHIP 1/10W R1255 1-216-295-91 SHORT CHIP R124 1-216-841-11 METAL CHIP 1/10W R1256 1-216-295-91 SHORT CHIP R125 1-216-833-11 METAL CHIP 1/10W R1261 1-216-833-11 METAL CHIP...
  • Page 66 HCD-GTR88 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C1516 1-162-970-11 CERAMIC CHIP 0.01uF R1527 1-216-809-11 METAL CHIP 1/10W C1517 1-100-597-91 CERAMIC CHIP 0.1uF R1530 1-216-857-11 METAL CHIP 1/10W C1518 1-100-597-91 CERAMIC CHIP 0.1uF R1533...
  • Page 67 HCD-GTR88 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C147 1-126-959-11 ELECT 0.47uF C292 1-162-964-11 CERAMIC CHIP 0.001uF C148 1-104-658-91 ELECT 100uF C149 1-126-947-11 ELECT 47uF C294 1-100-597-91 CERAMIC CHIP 0.1uF C150 1-100-597-91 CERAMIC CHIP 0.1uF...
  • Page 68 HCD-GTR88 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C656 1-100-597-91 CERAMIC CHIP 0.1uF IC253 8-759-278-58 IC NJM4558V-TE2 C697 1-100-597-91 CERAMIC CHIP 0.1uF IC254 8-759-278-58 IC NJM4558V-TE2 IC255 8-759-278-58 IC NJM4558V-TE2 C698 1-100-597-91 CERAMIC CHIP 0.1uF...
  • Page 69 HCD-GTR88 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark JR053 1-216-296-11 SHORT CHIP Q655 8-729-040-76 TRANSISTOR KTA1273-Y-AT JR054 1-216-296-11 SHORT CHIP JR055 1-216-296-11 SHORT CHIP Q656 8-729-620-07 TRANSISTOR 2SC3052EF-T1-LEF JR056 1-216-864-11 SHORT CHIP Q657 6-551-696-01...
  • Page 70 HCD-GTR88 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R099 1-216-801-11 METAL CHIP 1/10W R235 1-218-867-11 METAL CHIP 6.8K 0.5% 1/10W R236 1-218-867-11 METAL CHIP 6.8K 0.5% 1/10W R103 1-216-838-11 METAL CHIP 1/10W R240 1-216-833-11...
  • Page 71 HCD-GTR88 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R419 1-216-821-11 METAL CHIP 1/10W R582 1-216-821-11 METAL CHIP 1/10W R421 1-216-821-11 METAL CHIP 1/10W R585 1-216-835-11 METAL CHIP 1/10W R422 1-216-821-11 METAL CHIP 1/10W R587...
  • Page 72 HCD-GTR88 POWER AMP Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark MIC BOARD R716 1-216-845-11 METAL CHIP 100K 1/10W ********* R720 1-216-845-11 METAL CHIP 100K 1/10W R721 1-216-836-11 METAL CHIP 1/10W < CAPACITOR > R722 1-216-833-11...
  • Page 73 HCD-GTR88 POWER AMP SUBTRANS Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark D1306 6-501-817-01 DIODE MA2J1110GLS0 < RELAY > D1307 6-500-334-01 DIODE MC2836-T112-1 RY1300 1-755-653-11 RELAY D1310 6-501-817-01 DIODE MA2J1110GLS0 < TERMINAL > < IC >...
  • Page 74 HCD-GTR88 SUBWOOFER Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark SUBWOOFER BOARD ***************** R841 1-216-848-11 METAL CHIP 180K 1/10W R850 1-216-817-11 METAL CHIP 1/10W < CAPACITOR > (EXCEPT MX) R850 1-216-818-11 METAL CHIP 1/10W C800 1-126-947-11...
  • Page 75 HCD-GTR88 TRANS Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C537 1-162-966-11 CERAMIC CHIP 0.0022uF R513 1-216-845-11 METAL CHIP 100K 1/10W C538 1-162-970-11 CERAMIC CHIP 0.01uF R514 1-216-845-11 METAL CHIP 100K 1/10W R515 1-216-864-11 SHORT CHIP...
  • Page 76 HCD-GTR88 TRANS Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < HOLDER, FUSE > < RESISTOR > FH1250 1-533-217-41 HOLDER, FUSE R1001 1-216-817-11 METAL CHIP 1/10W FH1251 1-533-217-41 HOLDER, FUSE R1002 1-216-817-11 METAL CHIP 1/10W FH1252...

  • Page 77: Revision History

    HCD-GTR88 REVISION HISTORY Checking the version allows you to jump to the revised page. Also, clicking the version at the top of the revised page allows you to jump to the next revised page. Ver. Date Description of Revision 2010.04...

Table of Contents

Save PDF