2. When the cover is open, close viewing through the objective lens with the naked eye will cause exposure to the laser beam. ∗ : See page 29. /C LO M EN M EN DV-600AV-S...
Page 3
To protect products from damages or failures during transit, the shipping mode should be set or the shipping screws should be installed before shipment. Please be sure to follow this method especially if it is specified in this manual. DV-600AV-S...
11. PCB CONNECTION DIAGRAM ........................72 11.1 DVD MT PCB ASSY..........................73 11.2 OPERATION 1 PCB and OPERATION 2 PCB ASSYS................75 11.3 POWER PCB ASSY..........................76 11.4 USB PCB, LOADING MOTOR and SW ASSYS ..................78 12. PCB PARTS LIST ............................79 DV-600AV-S...
• Soldering time: Within 3 seconds • Soldering combination: Sn-3.0Ag-0.5Cu • When Soldering/Removing of solder, use the draw in equipment over the Pick Up Unit to prevent the Flux smoke from it. Short circuit using a soldering iron. Pick Up PCB Fig. 1 DV-600AV-S...
• Place the unit on a workstation equipped to protect against static electricity, such as conductive mat. • Soldering iron with ground wire or ceramic type is used. • A worker needs to use a ground conductive wrist strap for body. DV-600AV-S...
Super VCD also supports the widescreen size. * Edit points may not play exactly as edited; screen may go momentarily blank at edited points. • Unfinalized playback: No Super VCD • MP3/WMA/MPEG-4 AAC/JPEG or DivX video/WMV file playback on DVD-R/-RW: DV-600AV-S...
CD-R/-RW/-ROM discs. Keeping the same terminology as DVD-Video, individual DivX video files are called ˝Titles˝. When naming files/titles on a CD-R/-RW disc prior to burning, keep in mind that by default they will be played in alphabetical order. DV-600AV-S...
Press to turn to USB MODE. Press once again to return to DVD mode. 16 USB port (Type A) Connect USB device Compatible This mark indicates compatibility with DVD-RW discs recorded on a DVD recorder in Video Recording mode. DV-600AV-S...
Page 12
Use to navigate on-screen displays and Press to display a DVD disc menu, or the Disc menus. Press ENTER to select an option or Navigator if a VR format DVD-RW, CD, Video CD , MP3, WMA or JPEG disc is loaded. execute a command. DV-600AV-S...
Page 13
Press to jump to the next chapter or track. Press to stop the disc (you can resume playback by pressing (play)). 23 DISPLAY Press to display information about the disc playing. 24 ZOOM Press to change the zoom level. DV-600AV-S...
Items to be checked regarding video Item to be checked regarding audio Block noise Distortion Horizontal noise Noise Dot noise Volume too low Disturbed image (video jumpiness) Volume too high Too dark Volume fluctuating Too bright Sound interrupted Mottled color DV-600AV-S...
• Before shipping out the product, be sure to clean the following positions by using the prescribed cleaning tools: Position to be cleaned Position to be cleaned Cleaning tools Cleaning tools Remark Remark Pickup leneses Cleaning liquid : GEM1004 Cleaning paper : GED-008 DV-600AV-S...
FL DC- FL DC- FL DC+ FL DC+ -28V -28V POWER PCB PCB240 DPF015 USB PCB ASSY (A2K401ADD0) USB PCB PCBDD0 DEF133 NOTE : THE TIMETHIS INTERCONNECTION DIAGRAM IS THE LATEST AT OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE. DV-600AV-S...
: LES PIECES REPAREES PAR UN > ETANT CAUTION : SINCE THESE PARTS MARKED BY > ARE DANGEREUSES AN POINT DE VUE SECURITE N’UTILISER QUE CELLS DECRITES CRITICAL FOR SAFETY,USE ONES DANS LA NOMENCLATURE DES PIECES. DESCRIBED IN PARTS LIST ONLY DV-600AV-S...
DECK DOES NOT ACCEPT OPEN/CLOSE Is the voltage at Check P.CON 6V line of pin 8,19 and 28 of IC2301 POWER BLOCK. about DC6V ? Check CD2302 Is the lose connection connection to DECK. at CD2302 to DECK ? Change DVD LOADER. DV-600AV-S...
Page 24
Replace V651 or IC651. NO PLAYBACK PICTURE OF AV JACK Is there Check IC4002 and a signal at pin 187 of peripheral circuit. IC4002 ? Is there Check J7302 and peripheral video signal at pin 33 circuit. of IC7301 ? Change IC7301. DV-600AV-S...
Page 25
AUDIO signal at pins 7 and 8 circuit. of IC8003 ? Is there Is there Check AT +5V. voltage at pin 6 of IC8003 waveform at pins 1,2 about 5V ? and 3 0f IC8003 ? Change IC8003. Change IC4002. DV-600AV-S...
Page 26
When 21 pin output is RGB, Is there voltage at pin 16 of connection. 21pin about 4.5V (No load)? Is the Check Q8104, Q8105 and voltage at pin 188 of IC4002 peripheral circuit. about 3.3Vp-p ? Check IC4002 and peripheral circuit. DV-600AV-S...
Page 27
Any kind of symptoms (no power, a failure in any of the servo, video and audio systems, etc.) may be (DVD MT PCB Assy : IC4002) generated, because the DVD processing is performed by a single chip. 64M SDRAM No power. (DVD MT PCB Assy : IC4005) Block noise is generated during playback. DV-600AV-S...
Assy. If the voltage is 0.4 V or higher, the 780-nm LD is degraded. DVD MT PCB ASSY R4044 W822 R4051 Q4004 DMF090A Q4002 R4058 R4003 W816 W864 R4064 R4065 R4026 R2327 R7304 R7317 W807 Q7302 R8004 R8086 W822 Q8025 R4058 R8084 W809 R8066 Q8021 W808 R8065 R8061 R8028 SIDE B DV-600AV-S...
• After going into service mode, if you play back the disc, "DISC-NON" is displayed. • The video signal and the audio signal are outputted during the servicemode. • The SKIP key and the SCAN key are effective during the service mode. SERVICE MODE: OFF POWER GGF1381 Service mode remote control unit DV-600AV-S...
3 LD ON DVD : Press the [TEST] (A8-5E) and [1] (A8-01) keys in order, and turn on the laser diode (650n). : Press the [TEST] (A8-5E) and [4] (A8-04) keys in order, and turn on the laser diode (780n). DV-600AV-S...
: [NTSC] PAL system : [PAL] Automatic setting : [AUTO] Scart terminal output [SK – ∗ ∗] (Display only the WY model which can do the output setting of scart terminal.) VIDEO : [00] S-VIDEO : [01] : [02] DV-600AV-S...
• Region confirmation mode (ESC + A.MON [Service mode remote control unit] + "1"-"8" [Service mode remote control unit] keys) After you press the A.MON key while holding the ESC key pressed and then input the region number, if the number is different from that set in the unit, an error message is displayed, and the tray opens. DV-600AV-S...
%%e -2 : NG 7.0e -4 : NG 3 EDC/ID error history (ID Address, EDC/ID errors, last eight errors) Note: ∗ Error of AV1 is not supported in this player. Indication plan contents Character in bold : Item name : Information display DV-600AV-S...
Short circuit using a soldering iron. 1. Disconnect the following connectors: (CP6601 and CP6602). 2. Remove the 2 screws 1. 3. Remove the USB PCB in the direction of arrow. DVD Deck Pick Up PCB USB PCB Fig. 1-4 Fig. 1-2 DV-600AV-S...
Page 35
PCB and DVD MT PCB connector. 1-5: DVD MT PCB (Refer to Fig. 1-5) 1. Remove the 4 screws 1. 2. Remove the 4 screws 2. 3. Remove the DVD MT PCB in the direction of arrow. DVD MT PCB Fig. 1-5 DV-600AV-S...
Page 37
3 supports 1. between A and B. Fig. 2-3-D 2. Remove the Plate Clamper, Magnet Clamper and Clamper. Check Hook Check Hook Plate Clamper Magnet Clamper Main Frame Loading Motor PCB Ass’y Check Hook Clamper Fig. 2-3-E Fig. 2-5-A DV-600AV-S...
Page 38
6. Remove the Switch PCB Ass'y. 7. Remove the screw 4. Feed Motor 8. Remove the Gear Feed. 9. Remove the 2 screws 5. 10. Remove the Feed Motor. Safety surface for pressing 11. Remove the Gear Motor. of the insert. Fig. 2-7-C DV-600AV-S...
Page 39
Fig. 2-8. NOTE 1. Do not make the folding lines except the specified positions for the FFC. [ 24 pin FFC ] Fold Printing Surface 79 ± 1 mm Reinforcement Plate To Pick Up PCB Fig. 2-8 DV-600AV-S...
While the screen shown at left is being displayed, updating is in progress. DO NOT TURN OFF THE POWER DURING UPDATING. 4 Updating of the firmware is completed. When the screen with the Pioneer logo is displayed, updating is completed. The time required for updating is about 2 minutes. DV-600AV-S...
Page 41
2 If updating of the firmware using the disc for updating failed • Was the disc for updating recognized properly? Check if the volume label of the disc is PIONEER. • Is playback of a disc other than the disc for updating possible? If playback of a test CD is also impossible, a reading section, such as PU, may be defective.
For the applying amount of lubricants or glue, follow the instructions in this manual. (In the case of no amount instructions, apply as you think it appropriate.) 9.1 PACKING SECTION YXZTUR5 Only Except WVXZT5 WVXZT5 Only YXZTUR5 Only YXZTUR5 Only YXZTUR5 Only DV-600AV-S...
Page 43
See Contrast table (2) Operating Instructions (S/D) See Contrast table (2) Operating Instructions (R) See Contrast table (2) (2) CONTRAST TABLE DV-600AV-S/WYXZT5, /WVXZT5, /YXZTUR5, DV-600AV-K/WYXZT5 and YXZTUR5 types are constructed the same except for the following : DV-600AV-S/ DV-600AV-S/ DV-600AV-S/ DV-600AV-K/ DV-600AV-K/ Mark No.
9.2 EXTERIOR SECTION NON-CONTACT SIDE CONTACT SIDE DV-600AV-S...
Page 45
Spring Earth 753WUAA012 Screw,Tap Tite(B) (3x6.0) See Contrast table (2) Screw,Tap Tite(B)Pan (3x6) 810913060U (2) CONTRAST TABLE DV-600AV-S/WYXZT5, /WVXZT5, /YXZTUR5, DV-600AV-K/WYXZT5 and /YXZTUR5 types are constructed the same except for the following : DV-600AV-S/ DV-600AV-S/ DV-600AV-S/ DV-600AV-K/ DV-600AV-K/ Mark No.
Note : (SW PCB ASS'Y) CD2301 NOTE: Applying positions AA, AB and AC for the CLASS PART NO. MARK grease are displayed for this section. GREASE GEM1018 Check if the correct grease is applied for each GYA1001 position. GEM1036 DV-600AV-S...
MMZ1608R102CT TP4103 PWR# PCE# PRD# NOTE : THE DC VOLTAGE EACH PART WAS MEASURED NOTE : THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME WITH THE DIGITAL TESTER DURING PLAYBACK. OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE. DV-600AV-S...
C4040 DCAS# DRAS# DBA1 DBA0 NC (WP#/ACC) SDCLK DCS# RY/BY# PRD# PCE# PRD# PCE# PWR# FROM POWER PORT (V+3D) D_GND NOTE : THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE. DV-600AV-S...
Page 51
LDQM DQM1 DWE# UDQM SDCLK DCAS# CAS# SDCKE DRAS# RAS# DCS# MA11 DBA0 BA0/A13 DBA1 BA1/A12 MA10 A10/AP C4123 0.1 B TP4050 PCB130 DMF090 NOTE : THE DC VOLTAGE EACH PART WAS MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK. DV-600AV-S...
: SINCE THESE PARTS MARKED BY > ARE : LES PIECES REPAREES PAR UN > ETANT DANGEREUSES CRITICAL FOR SAFETY, USE ONES DESCRIBED AN POINT DE VUE SECURITE N’UTILISER QUE CELLS DECRITES IN PARTS LIST ONLY. DANS LA NOMENCLATURE DES PIECES. DV-600AV-S...
Page 53
2.63 VOTK+ VOFC+ PCB130 NOTE : THE DC VOLTAGE EACH PART WAS MEASURED WITH NOTE : THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME DMF090 THE DIGITAL TESTER DURING PLAYBACK. OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE. DV-600AV-S...
: SINCE THESE PARTS MARKED BY > ARE POINT DE VUE SECURITE N’UTILISER QUE CELLS DECRITES CRITICAL FOR SAFETY, USE ONES NOTE : THE DC VOLTAGE EAC DANS LA NOMENCLATURE DES PIECES. DESCRIBED IN PARTS LIST ONLY. WITH THE DIGITAL TE DV-600AV-S...
Page 55
CAUTION: DIGITAL TRANSISTOR PCB130 DMF090 TE : THE DC VOLTAGE EACH PART WAS MEASURED NOTE : THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME WITH THE DIGITAL TESTER DURING PLAYBACK. OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE. DV-600AV-S...
FROM POWER PORT W889 V+3F TP7303 D_GND V+6A NOTE : THEDURING PLAYBACK.MEASURED WITH THE NOTE : THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME DIGITAL TESTER DC VOLTAGE EACH PART WAS. OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE. DV-600AV-S...
Page 57
VIDEO/AUDIO for 21PIN CP7301 IMSA-9604S-12C 21PIN-G/D-Y 21PIN-B/D-U 21PIN-R/D-V P-H/I-L_RGB-H RGB-H ASP/FS CVBS AUDIO L AUDIO R TP7301 CVBS 4CH BUS SW IC IC7302 SN74CBT3257PWR CVBS/Y/U/V S-VIDEO OUT for HE J7302 J7304 RCA-405A-08 DIN-409A PCB130 CAUTION : DIGITAL TRANSISTOR DMF090 DV-600AV-S...
DVD MT PCB ASSY (6/7) (A2K501A130) FROM POWER PORT V+5H D_GND FROM/TO MPEG/MICON/DSP TX2+ TX2- TX1+ TX1- TX0+ TX0- TXC+ TXC- HDMI_SCL HDMI_SDA W855 A_GND W856 W861 A_GND NOTE : THE DC VOLTAGE EACH PART WAS MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK. DV-600AV-S...
Page 59
TXC+ TXC+ CLK+ L5904 CLK-S EXC24CG900U TXC- TXC- CLK- HDMI_SCL HDMI_SDA W840 POWER HOTPLUG V+5H W851 W858 W864 PCB130 NOTE : THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME DMF090 OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE. DV-600AV-S...
: LES PIECES REPAREES PAR UN > ETANT CAUTION : SINCE THESE PARTS MARKED BY > ARE DANGEREUSES AN POINT DE VUE SECURITE NOTE CRITICAL FOR SAFETY,USE ONES N’UTILISER QUE CELLS DECRITES DESCRIBED IN PARTS LIST ONLY. DANS LA NOMENCLATURE DES PIECES. DV-600AV-S...
Page 61
FRROM/TO MEMORY D_GND NOTE : THE DC VOLTAGE EACH PART WAS PCB130 DMF090 MEASURED WITH THE DIGITAL TESTER NOTE : THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME DURING PLAYBACK. OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE. DV-600AV-S...
Vout R666 1/4W OS651 ROM-V340TAO NOTE : THE DC VOLTAGE EACH PART WAS MEASURED WITH THE DIGITAL TESTER NOTE : THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME DURING PLAYBACK. OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE DV-600AV-S...
Page 63
CP601 (CP4002) 00_6232_011_102_800+ FP_SCK FP_DI DI (M to F) FFC(1.0mm pitch) FP_DO DO (F to M) CD601 V+3E 2H0B1003 V+3E V+3E C604 DGND C605 33P CH DGND TP663 1/4W FLDC+ 0.001 B FLDC+ -28V -28V FLDC- FLDC- PCB270 DEF126 DV-600AV-S...
: LES PIECES REPAREES PAR UN > ETANT NOTE : THE RESISTOR MARKED F IS FUSE RESISTOR. DANGEREUSES AN POINT DE VUE SECURITE THE ALUMI ELECTROLYTIC CAPACITOR MARKED NP N’UTILISER QUE CELLS DECRITES IS NON POLAR ONE. DANS LA NOMENCLATURE DES PIECES DV-600AV-S...
Page 65
CAUTION: DIGITAL TRANSISTOR PCB240 NOTE : THE DC VOLTAGE EACH PART WAS DPF015 NOTE : THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME MEASURED WITH THE DIGITAL TESTER OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE. DURING PLAYBACK. DV-600AV-S...
11.4 12.1 R8101 4.7K 1/4W NOTE : THE DC VOLTAGE EACH PART WAS NOTE : THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME MEASURED WITH THE DIGITAL TESTER OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE DURING PLAYBACK. DV-600AV-S...
Page 67
C8115 R8113 CVBS_VIDEO_OUT 6.3V 1000 YK_P 75 +-1% DVD_RGB_H_OUT Q8105 KRA102SRTK R8109 DVD_RGB_H_OUT Q8104 68 +-1% KRC104SRTK * The parts except mark cannot be changed. On that occasion, replace whole Assy. CAUTION: DIGITAL TRANSISTOR CAUTION: DIGITAL TRANSISTOR PCB240 DPF015 DV-600AV-S...
HIGH SIDE SW IC (60 OHM 2.5A) IC6601 RT9702-PB (SCHOTTKY 3.0A) 2H063401 B6601 D6601 VOUT HCB2012K-600T25 RB051L-40 TO POWER PCB CP6602 A2001WR2-4P P.CON+5V /FLG P.CON+5V CORD CONNECTOR CD6602 E8241203 NOTE:THE DC VOLTAGE EACH PART WAS MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK. DV-600AV-S...
Page 69
600T25 RB051L-40 CP6603 USB-A1D05F-4B4N W809 USB_DN W810 USB_DP C6610 W801 100P CH NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. PCBDD0 DEF133 DV-600AV-S...
Symbol In PCB Symbol In Schematic Part Name Diagrams Diagrams C E B Capacitor Connector Transistor B C E SIDE A Transistor with resistor B C E Field effect SIDE B P.C.Board Chip Part transistor Resistor array 3-terminal regulator DV-600AV-S...